Bissoy.com
Doctors Medicines MCQs Q&A

In the proportioning pump, two speed pump has a non-synchronous _____ rpm motor.

In the proportioning pump, two speed pump has a non-synchronous _____ rpm motor. Correct Answer 45 rpm

Proportioning pumps are available either for single-speed or for two-speed operations. The single-speed pump has the capacitor synchronous gear head utilizing 10 rpm output shaft at 50 Hz. The two-speed pump has a non-synchronous 45 rpm motor.

Related Questions

What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
A centrifugal pump which circulates a hot liquid metal at 500 degree Celsius is driven by a 3600 rpm electric motor. The motor is coupled to the pump impeller by a horizontal steel shaft of dia 25 mm. Let us assume the motor temperature as 60 degree Celsius with the ambient air at 25 degree Celsius, what length of shaft should be specified between the motor and the pump? It may be presumed that the thermal conductivity of the shaft material is 35W/m K and that the convective film coefficient between the steel shaft and the ambient air is 15.7W/square m K
A fan running at a speed of 280 rpm circulates 105 m3/s of air in a mine. If the power input to the motor for driving the fan is recorded to be 75 kW, with the combined efficiency of fan and motor at 70%. If the fan pressure is to be increased by 200 Pa by changing the fan speed. the fan speed in rpm will become
A 3-phasle, 6-pole, 50 Hz induction motor has a full load speed of 960 rpm with its slip rings short circuited. The motor drives the constant load. If the speed is reduced to 800 rpm, then ohmic losses will _________
A 3-phase, 6-pole, 50 Hz induction motor has a full load speed of 960 rpm with its slip rings short circuited. The motor drives the constant load. If the speed is reduced to 800 rpm, then ohmic losses will be?
A 3-phase, 6-pole, 50 Hz induction motor has a full load speed of 960 rpm with its slip rings short-circuited. The motor drives the constant load. If the speed is reduced to 400 rpm, then ohmic losses will be?
A student performs an experiment with a Francis turbine. He accidently set the RPM of Francis turbine to 1400 rpm instead of 700 rpm. He reported the power to be 1 MW. His teacher asks him to perform the same experiment using the correct RPM. The student performs the same experiment again, but this time the erroneously doubled the flow velocity. What does the student report the power to be?
The speed of a motor falls from 1200 rpm at no-load to 1050 rpm at rated load. The speed regulation of the motor is ____________
If Rati travels at his usual speed for ‘x’ hours, he covers the same distance as he covered when he travels at a speed 30 km/hr less than usual, but for (x + 3) hours. Which of the following can be determined? (A) If he travels at 20 km/hr less speed than usual, he can cover a distance of 240 km in (x - 1) hours. What is the value of ‘x’? (B) If travels at his usual speed for (t + 2) hours, and at 50% of his usual speed for (t - 2) hours, his average speed for the journey is 68 km/hr. What is his usual speed? (C) His usual speed (in km/hr) is a multiple of 5 between 40 and 50 (both inclusive). If ‘x’ is a whole number, what is his usual speed? (D) If he travels at his usual speed for ‘t’ hours, he covers a distance of 400 km. What is the value of ‘x’?
Consider the following statements: In the above figure, the curves pertain to the DC motor A. Speed vs Armature current characteristic of a DC shunt motor B. Torque vs Armature current characteristic of a DC shunt motor C. Speed vs Armature current characteristic of a DC series motor D. Torque vs Armature current characteristic of a DC series motor