Bissoy.com
Doctors Medicines MCQs Q&A

Which of the following are the types of Longitudinal stress?

Which of the following are the types of Longitudinal stress? Correct Answer Tensile stress, Compressive stress

Longitudinal stress is one the type of stress. Longitudinal stress is of two types. It consists of Tensile stress and Compressive stress. It has a unit of N/m2.

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Two plates are joined by double strap butt joints with rivets arrangement as shown in the figure. Width of the plate is 300mm and diameter of rivets 30mm. The thickness of the plates can be taken as 20mm. Allowable stress in tension, shear and compression are 80 N/mm²,60 N/mm² and 160N/mm². If circumferential stress is P, then longitudinal stress in the pressure vessel is?
The circumferential hoop stress and longitudinal stress are both shear stress.
A manufacturing company produces 5 types of chairs in two sizes - Regular" and "Large". The pie charts represent the total number of five types of chairs produced and the table shows the ratio between the number of regular sized and large sized chairs of five types. Type of Chair A B C D E Ration between Number of Regular Size and Large Size Chairs 3 : 2 4 : 5 3 : 1 5 : 3 3 : 8   If the total number of all types of chairs produced is 7200, what is the total number of regular size chairs of all types produced.
Consider the following statements: 1. The working stress design is based on explicit consideration of the various conditions under which the structure may cease to fulfill its intended function. 2. In the case of working stress design, the structure will directly take into consideration the various relevant modes of failure. 3. In the working stress method, regulatory bodies or classification societies usually specify the value of the allowable stress as some fraction of the mechanical properties of materials Which of the above statements is/are correct?
The following curves represent the constant stress creep curve. Sample A, B, C, D are tested at different stress values. The correct relationship of the magnitude of stress for the following stress values will be _________
Consider the following statements: The basic reason why shafts are made of steel and its alloys is: 1. The shaft is subjected to normal stress. 2. The shaft stress alternates with respect to time. 3. The shaft is subjected to pure compressive stress. 4. The shaft is subjected to the stress of constant intensity. Which of these statements are correct?