Bissoy.com
Doctors Medicines MCQs Q&A

For an SCR the total turn-on time consists of i) Delay time ii) Rise time and iii) Spread time During the rise time the

For an SCR the total turn-on time consists of i) Delay time ii) Rise time and iii) Spread time During the rise time the Correct Answer losses are maximum

The losses are maximum during the rise time because both Ia & Va are high.

Related Questions

For an SCR the total turn-on time consists of i) Delay time ii) Rise time and iii) Spread time During the delay time the
For an SCR the total turn-on time consists of i) Delay time ii) Rise time and the iii) Spread time The spread time interval depends upon
Consider the following statements: 1. In a silicon controlled rectifier (SCR), if the cathode gate is reverse-biased, then the SCR cannot fire at all. 2. The turn-on time of an SCR increases with temperature. 3. After an SCR is turned on, it can be made to turn off again by reverse biasing the gate. 4. Gate recovery time is the minimum time that the anode voltage must be maintained below holding voltage VH to turn off the SCR. Which of these statements are correct?
Each of the question below consists of a question and three statements number I, II and III given below it. You have to decide whether the data provided in the statement are sufficient to answer the question. Two person X and Y together can make 25% of total number of bricks in 4.8 days. Another person Z can make 50 bricks in a day. What is the time taken by person X and Z together to make the total number of bricks? I. Dimensions of a brick is (3cm × 4cm × 5cm) while the dimension of a cuboids when all the bricks are put together is (72cm × 80cm × 50cm) and ratio of number of days taken by X and Y alone to make the total number of bricks is 3 : 2. II. The total number of bricks is 4800 and person Y can make 150 bricks in day. III. Total volume of all the bricks together is 1.008m3 and dimension of a bricks is (5cm × 6cm × 7cm) and time taken by Z to make total number of bricks is 200 % more than the total time taken by person Y to make total number of bricks.
A voltage source Vs = Vm sinωt is connected in series with a resistance R and an SCR. At some firing angle delay of α a positive gate pulse is applied to the SCR which turns on the SCR. Considering ideal conditions, at the instant α the voltage at the resistor terminals Vo
The given bar graph represents data of the production of paper (in ten lakh tonnes) by three different companies X, Y and Z during the years 2008 to 2012. The x-axis shows the 'years' and the y-axis represents the 'production of paper (ten lakh tonnes)'. (Note: The data shown is only for mathematical exercise. They do not represent actual figures.)  The total production of Company Y during 2008 and 2009 and Company X for 2011 and 2012 taken together is p% (p is correct to the nearest integer) more than the total production of Company Z during 2010, 2011 and 2012. The total production of Company Z during 2008 and 2009 taken together is q% (q is correct to the nearest integer) less than the total production of Company X during 2008, 2009 and 2012 and Company Y during 2010 and 2011 all together.  What is the positive difference between p and q ? 
Consider the following statements: 1. The delay time is the time required to reach 50% of the final value in the first time. 2. The rise time is the time required for the response to rise from 10% to 90% of its final value for underdamped systems. 3. The rise time is the time required for the response to rise from 0 to 100% for the underdamped systems. Which of these statements are correct?
A 220 1-ϕ, 220 Ω  resistor is connected in series with the gate of an SCR as shown in the given figure. The gate current required to fire the SCR is 7 mA. what is the input voltage (Vin) required to fire the SCR?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise -fall periods and rise and fall periods should be same. The maximum rise in follower is 30 mm. How much the follower will rise when the follower is 120 degrees from its initial position of a cam?
A cam should be designed only using uniform rise and fall within half of the cam, the remaining is dwell period, and without any dwell period in between the rise-fall periods and rise and fall periods should be same. The maximum rise in follower is 45 mm. How much the follower will rise when the follower is 45 degrees from its initial position of a cam?