Bissoy.com
Doctors Medicines MCQs Q&A

What is the use of the AD0 pin?

What is the use of the AD0 pin? Correct Answer I2C Slave Address LSB Pin

The AD0 pin is the I2C Slave Address LSB pin on the MPU 6050. This is 0th bit in 7-bit slave address of device. If connected to VCC then it is read as logical HIGH and slave address changes.

Related Questions

There is a numeric lock which has a 3-digit PIN. The PIN contains digits 1 to 7. There is no repetition of digits. The digits in the PIN from left to right are in decreasing order. Any two digits in the PIN differ by at least 2. How many maximum attempts does one need to find out the PIN with certainty?
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin. What will be the new radius of gyration?
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. If two masses are used instead of the connecting rod, one at the gudgeon pin and other at the crank pin, if the angular acceleration of the rod is 23 000 rad/s2, then find the correction couple in N-m.
Each question presents a situation and asks you to make a judgement regarding that particular circumstance. Choose an answer based on given information. Aman has a debit card of XYZ bank. The card has 4-digit pin. Aman has not used his card for a while. He does not remember the pin even though he remembers some of the key points. 1. The 2nd digit was even number but not 2. 2. The 4th digit was 6. 3. The 3rd digit from the left was an odd number greater than 5. 4. The 1st digit from the left was an even prime number. Which of the following would be most likely the pin number?
In the following question below are given three statements followed by three conclusions. Taking the given statements to be true even if they seem to be at variance from commonly known facts, read all the conclusions and then decide which of the given conclusion logically follows the given statements. Statements: I. No pin is silver. II. All silver are metal. III. Some metal are gold. Conclusions: I. No metal is pin. II. Some pin are gold. III. Some gold are silver.
Read the instructions below and answer the questions that follow: P + Q means “some P are Q”. P – Q means “all P are Q”. Now, statements below are followed by two conclusions. You have to take the given statements to be true even if they seem to be at variance from commonly known facts. Read all the conclusions and then decide which of the given conclusions logically follows from the given statements disregarding commonly known facts. Statements: Sink + pin Pin + can Can – gun Gun + tin Conclusions: I. Gun + pin II. Can + tin
An Internal combustion engine has a connecting rod of mass 2 kg and the distance between the centre of crank and centre of gudgeon pin is 25 cm. The Center of Gravity lies at a point 10 cm from the gudgeon pin along the line of centres. The radius of gyration of this system about an axis through the Center of Gravity perpendicular to the plane of rotation is 11 cm. Find the mass located at gudgeon pin in Kg.
A flange mounted shear pin is used on a shaft as a safety device. The steel shear pin has a diameter of 2.38 mm and is to be mounted on the flange of shaft rotating at 650 rpm. The maximum power transmitted by the shaft is 4.5 KW. If the shear strength of material of pin is 30 MPa, the radial distance of its mounting is ____
The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity $${\omega _1}$$ rad/s in the clockwise direction and the link OB turns with angular velocity $${\omega _2}$$ rad/s in the anticlockwise direction, then the rubbing velocity at the pin joint O is (where r = Radius of the pin at O)
The two links OA and OB are connected by a pin joint at O. If the link OA turns with angular velocity $${\omega _1}$$ rad/s in the clockwise direction and the link OB turns with angular velocity $${\omega _2}$$ rad/s in the clockwise direction, then the rubbing velocity at the pin joint O is (where r = Radius of the pin at O)