Bissoy.com
Doctors Medicines MCQs Q&A

What type of cable is used in ARINC 629?

What type of cable is used in ARINC 629? Correct Answer Unscreened twisted pair

The ARINC 629 links and bus uses an unscreened twisted pair of wires with a connection to the bus through demountable current transformer couplers. Mil STD 1553 uses screened twisted pair cables. Parallel lines are rarely used today.

Related Questions

S1: Instantly the full load yanked Gordy towards the side of the bridge.
P: But the pull of the cable was too much.
Q: He could hardly feel the cable, slipping through his fingers, ripping off his gloves, and streaking over the railing like an escaping snake.
R: It smashed his hands hard against the top of the railing, causing a split - second feeling of fierce pain followed by numbness.
S: He held on to the cable; it had been hard work lifting it, and he did not want to have to start over again.
S6: Feeling a sharp burning sensation where the cable was speeding between his things, Gordy rose on tiptoe and as he did, the slithering coil of cable tightened around his left foot and yanked him over the railing.

The Proper sequence should be:
You are setting up a network in a school. You need to network 5 computers for the file and printer sharing. You want to use some donated cable and Ethernet adapters. You identify the donated adapters as ARCnet coaxial network adapters and 10Base2 Ethernet network adapters. You install an Ethernet adapter in each of the 5 computers and connect the donated cable. The computers are NOT able to maintain reliable communication. You suspect that you are NOT using the correct type of coaxial cable. Which type of coaxial cable should you be using?
A network administrator is connecting hosts A and B directly through their Ethernet interfaces, as shown in the illustration. Ping attempts between the hosts are unsuccessful. What can be done to provide connectivity between the hosts?

Subnetting mcq question image

1. A crossover cable should be used in place of the straight-through cable.
2. A rollover cable should be used in place of the straight-through cable.
3. The subnet masks should be set to 255.255.255.192.
4. A default gateway needs to be set on each host.
5. The subnet masks should be set to 255.255.255.0.
An English-based company has 629 men and 629 female employees in a collaborative project. The average attendance of all employees is 72 calls per day. On average, an average 72 calls are received by a male employee every day. What will be the average of the number of calls being added by the women staff daily?
Which of the following statements are true? a. In overhead lines, inductance is more predominant whereas capacitance is in the cable. b. In overhead lines, capacitance is more predominant whereas inductance is in the cable. c. Cost of cable is high compared to the overhead lines. d. Cost of cable is low compared to overhead lines
You have been given the task of installing cables for an Ethernet network in your office. The building is an older one, and-you have limited work space. In addition, the network cable will have to share the existing conduit with telephone cable, and cable segments will be up to 135 meters in length. Which cable is best suited to this installation?
Calculate the elongation of the cable due to load, if a steel cable of 2 cm diameter is used to lift a load of 500 π kg. Given that and the length of cable is 10 m and E = 2×106 kg/cm2.
Consider the following statements in connection with deflection-type and null-type instruments: 1. Null-type instruments are more accurate than the deflection-type ones. 2. Null-type of instrument can be highly sensitive compared to a deflection-type instrument. 3. Under dynamic conditions, null-type instruments are less preferred to deflection-type instruments. 4. Response is faster in null-type instruments as compared to deflection-type instruments. Which of the above statements are correct?
The assumptions for the calculations are done for the cable subjected to its own weight. In that one of the assumption is that the cable is flexible and the other is that the cable is ___________
Your 10Base2 Ethernet cable is 185 meters long. You are planning to extend your network by adding another 100 meters of cable. The total length of the cable will be 285 meters. The network uses NetBEUI. Which device should you use?