Bissoy.com
Doctors Medicines MCQs Q&A

What is the type of preload called when a bearing experiences a stress due to negative clearance?

What is the type of preload called when a bearing experiences a stress due to negative clearance? Correct Answer Bearing preload

When a bearing experiences a stress due to negative clearance then it is a type of bearing preload. These types of preload increases the bearing rigidity and helps in maintaining actual radial and axial position for displacement.

Related Questions

Consider the following statements: 1. Cross-section of a member of truss experiences uniform stress 2. Cross-section of a beam experiences minimum stress 3. Cross-section of a beam experiences linearly varying stress 4. Cross-sections of truss members experience only compressive stress Which of the above statements are correct?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
Which of the following are the functions of lubrication in a bearing unit ? 1. To protect the bearing components from corrosion. 2. To absorb heat from the bearing unit. 3. To carry heat away from the bearing unit. Select the correct answer using the code given below
Consider the following two statements regarding Bearing stiffeners provided at the location of a concentrated load: 1. Bearing stiffeners have to resist bearing and buckling loads. 2. Bearing area and the area resisting buckling load are the same. Which of the above statements is/are correct ?
A rotor which is balanced statically but not dynamically is supported on two bearings L apart and at high speed of the rotor, reaction on the left bearing is R. The right side of the bearing is shifted to a new position 2L apart from the left bearing. At the same rotor speed, dynamic reaction on the left bearing in the new arrangement will
What will be the renal clearance ratio of a drug whose renal clearance is 40ml/min and the clearance of creatinine is 95ml/min?
As per IS 800 ∶ 2007, in the design of beams/plate girders, when the web of a member acting alone is inadequate, different types of stiffeners are provided. Match the type of stiffeners provided in List I with the requirement to be satisfied by them in List 2. (Use the Code in the lists for matching). List 1 List 2 B. Intermediate transverse web stiffener 1. Provide local reinforcement to web under shear and bearing. C. Load carrying stiffener 2. Improve the buckling strength of a slender web due to shear. D. Bearing stiffener 3. Prevent local buckling of web due to concentrated loading. E. Diagonal stiffener 4. Prevent local crushing of web due to concentrated loading