Bissoy.com
Doctors Medicines MCQs Q&A

Slot fill type ball bearings have higher load bearing capacity than Conrad type ball bearing.

Slot fill type ball bearings have higher load bearing capacity than Conrad type ball bearing. Correct Answer True

Slot fill type ball bearings have higher load bearing capacity than Conrad type ball bearing. It is so because notches are present on the inner and outer surfaces of outer and inner race respectively. This facilitates more balls more ball to fit in the same amount of space which increases the load bearing capacity.

Related Questions

Five theatres PVR, DT, Chanakya, Regal and Maratha Mandir screen two out of ten films based on Romance, Thriller, Horror, Adventure, Children, Drama, Documentary, History, Religion and Cartoon. Each theatre exhibits only two films and allots two different slots for them, wherein slot I is before slot II. Chanakya screens a Horror film in the first slot, while Maratha Mandir exhibits a Historical film in the second slot. DT exhibits a thriller film in the second slot and Regal exhibits a documentary film. Drama must be exhibited only in the second slot. The children’s film and the Cartoon film are exhibited in the same theatre while the religious film is not in the first slot. If Chanakya screens a Religious film in its second slot, then which of the films can be screened by theatre Regal?
Consider the following statements in connection with thrust bearings: 1) Cylindrical thrust bearings have higher coefficient of friction than ball thrust bearings. 2) Taper rollers cannot be employed for thrust bearings. 3) Double-row thrust ball bearing is not possible 4) Lower race, outer race and retainer are readily separable in thrust bearings. Which of the above statements are correct?
Three pipes x, y and z can fill a tank A can fill it in 4 minutes. Two pipes p and q are connected to tank B. how much time does it take for both tanks to run at the full capacity? Ratio of time taken to fill tank A by P and time taken by x to fill tank A is 2: 1 and ratio of time taken by Q to fill tank B and Z to fill tank A is 5: 3. Pipe P is 20% more efficient then pipe Q. and pipe Y takes 12 minutes to fill the tank. Capacity of tank B is 3/4 times of tank A. Note: Tank B is to be filled only after filling tank A. Valves of pipe p and q are closed once tank B is running at full capacity.
Consider the following question and statements and decide which of the statements is sufficient to answer the question. There are seven balls of different size and colors: green yellow, blue, orange, red, pink and black. What is the order of the balls from largest to smallest? Statements: 1. The red ball is larger than the green ball. 2. The pink ball is the smallest. 3. The blue ball is the largest. 4. The green ball is larger than the yellow ball. 5. The yellow ball is larger than the orange and black balls.
Consider the following question and statements and decide which of the statements is sufficient to answer the question. There are seven balls of different size and colors: green, yellow, blue, orange, red, pink and black. What is the order of the balls from largest to smallest? Statements: 1. The red ball is larger than the green ball. 2. The pink ball is the smallest. 3. The blue ball is the largest. 4. The green ball is larger than the yellow ball. 5. The yellow ball is larger than the orange and black balls. 
A map shows the elevations of Darjeeling, Gangtok, Kalimpong, Pelling, and Siliguri. Kalimpong is at a lower elevation than Gangtok, Pelling is at a lower elevation than Gangtok. Pelling is at a higher elevation than Siliguri. Darjeeling is at a higher elevation than Gangtok. Which of the following statements can be inferred from the paragraph above? i. Pelling is at a higher elevation than Kalimpong ii. Kalimpong is at a lower elevation than Darjeeling iii. Kalimpong is at a higher elevation than Siliguri iv. Siliguri is at a lower elevation than Gangtok
Given below are two quantities named I and II. Based on the given information, you have to determine the relation between the two quantities. You should use the given data and your knowledge of Mathematics to choose among the possible answers. A man has two balls. The ratio of radius of first ball to that of the second ball is 7 : 3. Quantity I: If man cut the first ball from middle and difference between total surface area of part of first ball and total surface area of second ball is 1538.46cm2, then find the radius of smaller ball. Quantity II: If the sum of radius of two balls is 30, then what is the radius of first ball?
Ball bearings are preferred over other types of bearings for machines rated up to 75 kW. Which of the following is not true for ball bearings?
Two pipes are connected to tank 1 and one pipe connects tank 1 and tank 2 at the bottom of both tanks. At first pipe A and pipe B will filling tank 1 and then pipe C would be opened to fill tank 2. Capacity of tank 1 is twice capacity of tank 2. Pipe C takes 8 minutes to fill the whole tank 2 wherein discharging capacity of pipe C is 62.5 liters per minute. Ratio of time taken by pipe A and B to fill the tank when operating alone is 4 : 5 then find approximate discharging capacity of pipe A and B in liters/ minute if both the pipes discharge equal amount of water in tank. Time taken by pipe A and B to fill the tank 1 is 20/ 3 minutes
XYZ Limited is a small organization of eight employees. In order to ensure that there are no service interruptions, the HR department has prepared a lunch program for 'P, Q, R, S, T, U, V and W employees. From 1.00 am to 1.30 pm and from 1.30 pm to 2.00 pm there are only two scheduled times (slots) and the following conditions: a) Due to limited space to dine, the designated space (slot) can accommodate a maximum of five and a minimum of four employees. b) 'P' and 'S' will eat together. 'W' is not in that scheduled time (slot). c) 'Q' and 'R' cannot have lunch at the same time as 'S'. d) 'U' cannot have lunch with 'V' but with 'P' and 'T'. If V and W are having lunch at the scheduled time (slot) of 1.30 pm then who are the other people at the dinner table?