Bissoy.com
Doctors Medicines MCQs Q&A

CMOS inverter is used as SPDT switch in resistor DAC and is connected to the op-amp line. Find the output of CMOS, if the input applied is 1

CMOS inverter is used as SPDT switch in resistor DAC and is connected to the op-amp line. Find the output of CMOS, if the input applied is 1 Correct Answer Resistance is connected to input line

When Qbar =1, it makes transistor Q1-ON and Q2-OFF. The output of the CMOS inverter is 0v, connecting the resistance R1 to ground.

Related Questions

The price of a non-inverter AC is Rs. 7000 less than that of an inverter AC. If the sum of the prices of 5 inverter ACs and the prices of 3 non-inverter ACs is Rs. 315000 what is the percent by which the price of an inverter AC is more than that of the price of non-inverter AC?
You need to allow one host to be permitted to attach dynamically to each switch interface. Which two commands must you configure on your catalyst switch to meet this policy?
1. Switch (config-if) # ip access-group 10
2. Switch (config-if) # switchport port-security maximum 1
3. Switch (config) # access-list 10 permit ip host 1
4. Switch (config-if) # switchport port-security violation shutdown
5. Switch (config) # mac-address-table secure
During the calculation of load capacitance of a 1st stage CMOS inverter, the input node capacitances, Cgs, n and Cgs, p of the 2nd stage CMOS inverter is also considered.
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Consider the following statements about CMOS: 1. CMOS logic inverter has a maximum signal swing of 0 V to VDD. 2. The output signal swing is independent of the exact value of aspect ratio and other device parameters. 3. It is a fast switching device with wide noise margins. 4. It has zero input resistance and infinite output resistance. Which of these statements are correct?
The parallel combination of a 6.8 kΩ resistor and a 10 kΩ resistor is in series with the parallel combination of a 2.2 kΩ resistor and a 1 kΩ resistor. A 100 V source is connected across the circuit. The resistor(s) with the greatest voltage drop is (are)
Among the five objects, Gas stove, Washing machine, Refrigerator, Inverter and Microwave oven: the Washing machine is twice as heavy as the Inverter; the Gas stove is one and half time as heavy as the Microwave oven; the Washing machine and Microwave oven together weigh as much as the Gas stove and Inverter together; the Refrigerator and Inverter together are one and half times as heavy as the Gas stove. Which is the heaviest among the five objects?
Why the switches used in weighted resistor DAC are of single pole double throw (SPDT) type?
Which of the following statements are correct? (a) CMOS has a higher speed and smaller power than BJT. (b) CMOS ICs inputs should never be left unconnected as it may damage the device. (c) CMOS ICs with Schmitt trigger inputs are useful for better noise immunity. (d) CMOS is most popular logic family in VLSI Technology.
A word arrangement machine, When given an input line of words, rearranges it in every step following a certain rule. Following is an illustration of an input line of words and various steps of rearrangement.
Input: gone are take enough brought station
Step 1: take gone are enough brought station
Step 2: take are gone enough brought station
Step 3: take are station gone enough brought
Step 4: take are station brought gone enough
And Step 4 is the last step for this input. Now, find out an appropriate step in the following question following the above rule. Question:
Input: car on star quick demand fat
What will be the third step for this input ?