Bissoy.com
Doctors Medicines MCQs Q&A

The two adjustable parameters in single stub matching are distance‘d’ from the load to the stub position, and _________

The two adjustable parameters in single stub matching are distance‘d’ from the load to the stub position, and _________ Correct Answer Susceptance or reactance provided by the stub

Reactance or susceptance of the matching stub must be known before it used for matching, since it is the most important parameter for impedance matching between the load and the source.

Related Questions

In series stub matching, if the normalized impedance at a point on the transmission line to be matched is 1+j1.33. Then the reactance of the series stub used for matching is:
There are six people Kirti, Kavita, Komal, Khushi, Koel and Kritika, who got different positions in a competition. Kavita got second position while Khushi got third position from the last. Komal’s position was immediately after Kavita and immediately before Khushi. Koel does not get either the first position or the last position. Kirti also does not get the last position. Who got the last position?
There are seven persons Amit, Roshan, Ravi, Priya, Amrita, Arpita and Mitul. They participated in a competition where they got different positions. Amit scored the first position while Mitul scored the last position. Priya scored fourth position from the last. Ravi scored one position higher than Priya while Amrita scored one position lower than Priya. Roshan scored higher position than five of them. Who scored the second lowest position?
Consider the following statement: 1. Initial load tests and routine load tests are carried out on test piles and working Piles, respectively. 2. In a pile load test, the allowable load can be taken equal to half the ultimate load at which the total settlement amounts to one-tenth of the pile diameter. 3. In a pile load test, the allowable load can be taken equal to two-thirds of the total toad which causes a plastic settlement of 6 mm. Which of the above statements are correct?
If the normalized admittance at a point on a transmission line to be matched is 1+j1.47. Then the normalized susceptance of the stub used for shunt stub matching is:
Mohan traveled five cities (A, B, C, D and E) starting from home by a car which has a mileage such that the car can travel 10 km in 1 liter petrol. Distance between city A and B is twice the distance between home to city A. Distance between city B and C is thrice the distance between home to city A. Distance between city C and D is 100. Distance between city D and E is 1.5 times than the distance between B and C. Average distance traveled by Mohan was 41 km between five cities. Find how much petrol was needed by Mohan to travel from city B to D.
H, Y, T, U and P got different ranks based on their marks in the semester examination and viva. H got 3rd rank in the semester exam and 5th rank in the viva. T got 5th position in the semester and 1st position in the viva. P got 2nd position in both exams and viva. Y got 1st position in semester examinations and 4th position in the viva. Who got 3rd position in the viva?
In shunt stub matching, the key parameter used for matching is:
For series stub matching, the parameter used for matching is:
Questions below followed by two quantities. Find the relation between them. The table shows the distance travelled by five different boats upstream, the speed of the boat in still water and the time taken by them to cover the upstream distance. Boats Upstream distance Speed of boat Time taken  A  240 km  15 km/hr  20 hr  B  150 km  10 km/hr  25 hr  C  350 km  20 km/hr  50 hr  D  96 km  8 km/hr  16 hr  E  126 km  26 km/hr  9 hr   Quantity I: Boat B travel 238 km distance downstream in certain time. How much downstream distance boat D will cover at the same time? Quantity II: Boat E travel 722 km distance downstream in certain time. How much downstream distance boat A will cover at the same time?