Bissoy.com
Doctors Medicines MCQs Q&A

PD controller is used to compensate system. Compared to the uncompensated system, the compensated system has:

PD controller is used to compensate system. Compared to the uncompensated system, the compensated system has: Correct Answer Higher noise amplification

The compensated system of the proportional derivative controller has bandwidth increases and signal to noise ratio decreases. This implies higher noise amplification in a compensated system using a PD controller.

Related Questions

The block diagram of a feedback compensated system is given below: Which of the following statements are correct? a) When Kt = 0, the feedback compensation is in-effective and the system is uncompensated b) When Kt = 0, the feedback compensation is most effective and system is compensated c) The performance of the compensated system depends on Kt and T d) The performance of the compensated system does not depend on T
PD controller is used to compensate a system, Compared to the uncompensated system, the compensated system has:
The network formed by resistors and capacitors for modifying the rate of change of gain and the phase shift is called a compensating network. Which of the following statements are not correct ? (A) The main purpose of a compensating network is to modify the performance of op-amp ciruit over the desired frequency range (B) There are two types of op-amps : internally compensated and externally compensated (C) 741 C is an externally compensated op-amp while 709 C is internally compensated op-amp (D) The phase lag and phase lead are most commonly used compensating networks in op-amps (E) Phase lag contributes a positive phase angle and phase lead a negative phase angle Choose the most appropriate answer from the options given below : 
Consider the following statements: 1. Integral controller improves steady state response 2. By use of proportional controller, maximum peak overshoot decreases 3. Type and order of system reduces by one for derivative controller 4. Integral controller makes the system less stable in transient state due to oscillations Select the correct answer using the codes given below:
The effective SIL of a capacitor compensated line is ________ an uncompensated line.
On a non-pipelined sequential processor, a program segment, which is a part of the interrupt service routine, is given to transfer 500 bytes from an I/O device to memory.     Initialize the address register     Initialize the count to 500 LOOP: Load a byte from device     Store in memory at address given by address register     Increment the address register     Decrement the count     If count! = 0 go to LOOP Assume that each statement in this program is equivalent to a machine instruction which takes one clock cycle to execute if it is a non-load/store instruction. The load-store instructions take two clock cycles to execute. The designer of the system also has an alternate approach of using the DMA controller to implement the same transfer. The DMA controller requires 20 clock cycles for initialization and other overheads. Each DMA transfer cycle takes two clock cycles to transfer one byte of data from the device to the memory. What is the approximate speedup when the DMA controller based design is used in place of the interrupt driven program based input-output?
In a closed loop system, the process to be controlled is an integrating process with transfer function $$\frac{1}{{2{\text{s}}}}.$$ The controller proposed to be used in an integral controller with transfer function $$\frac{1}{{{{\text{T}}_1}{\text{s}}}}.$$  When a step change in set point is applied to such a closed loop system, the controlled variable will exhibit
Assertion (A): A PI controller increases the order of the system by units but decreases the steady state error. Reason (R): A PI controller introduces a pole at either the origin or at a desired points on the negative real axis.
In FACTS technology, the controller employed in the transmission system is always a single high-power Controller.
We describe a protocol of input device communication below: i) Each device has a distinct address. ii) The BUS controller scans each device in a sequence of increasing address value to determine if the entity wishes to communicate iii) The device ready to communicate leaves its data in the I/O register iv) The data is picked up and the controller moves to the step a Identify the form of communication best describes the I/O mode amongst the following.