Bissoy.com
Doctors Medicines MCQs Q&A

Meter can be isolated from the circuit in a basic D.C. electronic voltmeter.

Meter can be isolated from the circuit in a basic D.C. electronic voltmeter. Correct Answer True

Field effect transistor (FET) acts as a source follower and provides very high input impedance. BJT along with resistors form a balanced bridge circuit. As a result the meter circuit can be isolated from the main circuit.

Related Questions

Consider the following statements regarding electronic voltmeter. 1) The detection of low-level signals is not possible using the electronic voltmeter 2) MOSFET is used at the input of the electronic voltmeter 3) Vacuum tube voltmeters (VTVM) consumes more power as compared to any non-electronic voltmeter. Which of the following is / are incorrect?
The figure shows the circuit of a rectifier type voltmeter. The diode D2 1. Does not allow any current to flow through the meter durign negative half cycle. 2. Does not allow reverse leakage current to flow through the meter during negative half cycle. 3. Short circuits the meter during negative half cycle. Which of these statements are correct?
The figure below shows a circuit for an AC voltmeter. It utilizes a moving-coil meter that gives a full-scale reading when the average current flowing through it is 1 mA. The moving-coil meter has a 50-Ω resistance. The value of R that results in the meter indicating a full-scale reading when the input sine-wave voltage VI is 20 V peak-to-peak is
An average responding rectifier type electronic ac voltmeter has its scale calibrated in terms of the rms value of a sine wave. If a square wave voltage of peak amplitude of 100 V is measured using this voltmeter, what will be the reading indicated by the meter?
A resistance R is measured using the connection shown in the below figure. The current measured is 10 A on ranges 100A and the voltage measured is 125 V on 150 V range. The scales of the ammeter and voltmeter are uniform. The total number of scale divisions of the ammeter is 100 and that of the voltmeter is 150. The scale division can be distinguished. The constructional error of the ammeter is ± 0.3% and that of voltmeter±0.4%. The resistance of the ammeter is 0.25 Ω. The possible error in the measurement of R is?
Consider the following statements regarding reciprocity theorem : 1. In any passive linear bilateral network, if the single voltage source Vx, in branch x produces the current response Iy, in branch y, then the removal of the voltage source from branch x and its insertion in branch y will produce the current response iy in branch x. 2. The interchange of an ideal voltage source and an ideal ammeter in any passive, linear, bilateral circuit will not change the ammeter reading. 3. The interchange of an ideal current source and an ideal voltmeter in any passive linear bilateral circuit will change the voltmeter reading. Which of the above statements are correct ?
A middle school mathematics teacher distributes a piece of rope, 1 meter long, to her students. She asks them to make a list of things in their surroundings that are 1 meter long, slightly less or more than 1 meter, double or half of one meter. Which of the following statement(s) is/are true for the given situation? (a) It can be used as an activity to introduce standard unit of length measurement in a class. (b) It can be used to encourage children to estimate length of objects in daily life, (c) It is a good activity to establish the formula for conversion of metre to centimetre or vice-versa. (d) This type of activity should be given only as home task so that class time is utilised for solving the questions. Choose the correct option.
Select the option that is true regarding the following two statements labeled Assertion (A) and Reason (R). Assertion (A): Whenever we measure an electrical signal, there are chances of over current which leads to overheating of the meter. In such cases, the meter can be protected by using a semiconductor diode of suitable rating. Reason (R): As soon as the diode is short-circuited, the meter current is diverted through the diode. As a result, the meter is being protected from excess heating.
A rectangular swimming pool is 15 meter long and 30 meter wide. A deck, with uniform width, surrounds the pool. If the total area of the pool and deck is 1050 square meter what is the width of the deck in meter?
How many floor tiles of measurement  5 meter × 1 meter will be required for lying tiles in 30 meter long and 25 meter wide rectangular field?