Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

The Transfer characteristic of the different types of MOSFETs is shown below, where ID is drain current and VGS is the Gate-Source voltage, the correct combination of MOSFET w.r.t to transfer characteristics is: Types of MOSFET (P) P – Channel Enhancement MOSFET (Q) P – Channel Depletion MOSFET (R) N – Channel Enhancement MOSFET (S) N – Channel Depletion MOSFET
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Consider the amplifier below for the case VDD = 5 V, RD = 24 kΩ, (W/L) = 1 mA/V2, and Vt = 1 V. For amplifier biased to operate with an overdrive voltage of 0.5V, and disregarding the distortion caused by the MOSFET’s square-law characteristic, what is the largest amplitude of a sine-wave voltage signal that can be applied at the input while the transistor remains in saturation?
In a certain code language, ‘pin tin san' means 'pot is old’, 'tin san vin' means 'old is gold', 'san vin kin' means ‘there is gold’, 'vin san haw' means ‘gold is beautiful’. How can 'old is beautiful' be coded in that language?
In the question one statement is given, followed by two conclusions, I and II. You have to consider the statement to be true even if it seems to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statement. Statement: A function is a relation between a set of input elements and a set of possible output elements where each input is related to exactly one output. Conclusion I: Every input element is related to every output element. Conclusion II: Every input element is related to one element of the output.
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
Choose the correct statement(s) i) The gate circuit impedance of MOSFET is higher than that of a BJT ii) The gate circuit impedance of MOSFET is lower than that of a BJT iii) The MOSFET has higher switching losses than that of a BJT iv) The MOSFET has lower switching losses than that of a BJT
An amplifier without feedback has a voltage gain of 50, input resistance of 1 kΩ & Output resistance of 2.5 kΩ.The input resistance of the current shunt negative feedback amplifier using the above amplifier with a feedback factor of 0.2 is
Consider an inverting amplifier with a nominal gain of 1000 constructed from an op amp with an input offset voltage of 3 mV and with output saturation levels of ±10 V. If the effect of VOs(input offset voltage) is nulled at room temperature (250C), how large an input can one now apply if the circuit is to operate at a constant temperature?
A sinusoidal input voltage Vin of frequency ω is fed to the circuit shown in the figure, where C1 ≫ C2. If Vm is the peak value of the input voltage, then output voltage (Vout) is
Electronics mcq question image