Bissoy.com
Doctors Medicines MCQs Q&A

While measuring the output load capacitance Cgs, n and Cgs, p is not considered. Why?

While measuring the output load capacitance Cgs, n and Cgs, p is not considered. Why? Correct Answer Because Cgs, n and Cgs, p are the capacitances at the input nodes

Cgs, n and Cgs, p are gate to source capacitances of nMOS and pMOS transistors in CMOS inverter. They are measured at input node. Therefore they are not considered for calculation of load capacitance.

Related Questions

During the calculation of load capacitance of a 1st stage CMOS inverter, the input node capacitances, Cgs, n and Cgs, p of the 2nd stage CMOS inverter is also considered.
World Bank has employed major dimensions to construct measures of governance. These dimensions are:
1. Voice and Accountability - measuring political, civil and human rights
2. Instability an d violence - measuring the likelihood of violent threats to or changes in government, including terrorism
3. Government effectiveness - measuring the competence of the bureaucracy and the quality of public service delivery
4. Regulatory burden - measuring the incidence of market, unfriendly policies
5. Rule of law - measuring the quality of contract enforcement, the police, and the courts, as well as the likelihood of crime and violence
Select the correct answer:
Two capacitors having capacitance value 4F, three capacitors having capacitance value 2F and 5 capacitors having capacitance value 1F are connected in parallel, calculate the equivalent capacitance.
Consider the following components in a multi-stage R-C coupled amplifier: 1. Parasitic capacitance of transistor 2. Coupling capacitance 3. Stray capacitance 4. Wiring capacitance Which of the above components effectively control high frequencies?
Consider the following statement: 1. Initial load tests and routine load tests are carried out on test piles and working Piles, respectively. 2. In a pile load test, the allowable load can be taken equal to half the ultimate load at which the total settlement amounts to one-tenth of the pile diameter. 3. In a pile load test, the allowable load can be taken equal to two-thirds of the total toad which causes a plastic settlement of 6 mm. Which of the above statements are correct?
Mr. Justin wanted to test his students' understanding of the 'nature of weekly markets from a seller's point of view'. Which of the following questions are suited to test this? i. Can a weekly market address all the needs of a family? Why or why not? ii. Compare and contrast the characteristics of a weekly market and a permanent shop. iii. Are you likely to find a well-known brand as part of a weekly market? Why or why not? iv. Can any seller increase their price a lot compared to other sellers in a weekly market? Why or why not?
What is the load factor considered for steel structures when combination of dead load, imposed load and earthquake load is considered?
Wages of the workers are normally, the proportionality derived from their efficiency. But the concept of efficiency of labour is itself vague such as amount of physical output, output per man hour or output per man shift. But output is not the function of man alone. There are other factors which affect the output. Which among the following is/are not the factor(s) that would affect the output directly?
1. Physical condition of work
2. Nature of machinery
3. Technical process
4. Quality of raw material
5. System of management
6. Role of fellow workers
7. Competitors in the market
In connection with inspection and testing of concrete structures as per IS 456:2000, while conducting load tests on flexural members, what is the load (L) and minimum duration of load application(T) on the structure? (Use notations as : DL : dead Load, IL : Imposed load)
While teaching the correct method of measuring the volume of a solid using a measuring cylinder Kavita mentions the following steps (not in the correct sequence) to be followed: a. Note the reading of the level of water in cylinder b. Suspend the solid with a thread inside water in the cylinder c. Record the least count of the measuring cylinder d. Put sufficient water in the cylinder and note the reading Which one of the following is the correct sequence of steps for the said purpose?