Bissoy.com
Doctors Medicines MCQs Q&A

While CPU is executing a program, an interrupt exists then it

While CPU is executing a program, an interrupt exists then it Correct Answer breaks the normal sequence of execution of instructions

An interrupt function is to break the sequence of operation.

Related Questions

A computer handles several interrupt sources of which the following are relevant for this question. Interrupt from CPU temperature sensor (raises interrupt if CPU temperature is too high) Interrupt from Mouse (raises interrupt if the mouse is moved or a button is pressed) Interrupt from Keyboard (raises interrupt when a key is pressed or released) Interrupt from Hard Disk (raises interrupt when a disk read is completed) Which one of these will be handled at the HIGHEST priority?
Consider three software items: Program-X, Control Flow Diagram of Program-Y and Control Flow Diagram of Program-Z as shown below Program-X: Control Flow Diagram of Program-Y sumcal (int maxint, int value) {       int result=0, i=0;       if (value <0)       {           Value = -value;       }       while ( (i
Consider the following statements. I. Daisy chaining is used to assign priorities in attending interrupts. II. When a device raises a vectored interrupt, the CPU does polling to identify the source of interrupt. III. In polling, the CPU periodically checks the status bits to know if any device needs its attention. IV. During DMA, both the CPU and DMA controller can be bus masters at the same time. Which of the above statements is/are TRUE?
You install and run a third-party 32-bit application named Application on your Windows 2000 Server computer. After several days, the application stops responding. You open Task Manager and find that the CPU usage is at 100 percent. The normal range of CPU usage on the server is from 20 percent to 30 percent You end the application. However, you see that the CPU on the server is still at 100 percent. Task Manager shows no other applications running. You then examine the Processes page in Task Manager and confirm that the Application.exe process is no longer running. You want to return the CPU usage to its normal range. What should you do?
The _________ determines the cause of the interrupt, performs the necessary processing and executes a return from the interrupt instruction to return the CPU to the execution state prior to the interrupt.
At an Electronic Data processing unit, five out of the eight program sets P,Q,R,S,T,U,V and W are to be operated daily. On any one day, except for the first day of a month, only three of the program sets must be the ones that were operated on the previous day. The program operating must also satisfy the following conditions: 1. If program P is to be operated on a day, V can’t be operated on that day. 2. If Q is to be operated on a day, T must be one of the programs to be operated after Q. 3. If R is to be operated on a day, V must be one of the programs to be operated after R. 4. The last program to be operated on any day must be either S or U. If the program sets R and W are to be operated on the first day, which of the following could be the other program on that day?
On a non-pipelined sequential processor, a program segment, which is a part of the interrupt service routine, is given to transfer 500 bytes from an I/O device to memory.     Initialize the address register     Initialize the count to 500 LOOP: Load a byte from device     Store in memory at address given by address register     Increment the address register     Decrement the count     If count! = 0 go to LOOP Assume that each statement in this program is equivalent to a machine instruction which takes one clock cycle to execute if it is a non-load/store instruction. The load-store instructions take two clock cycles to execute. The designer of the system also has an alternate approach of using the DMA controller to implement the same transfer. The DMA controller requires 20 clock cycles for initialization and other overheads. Each DMA transfer cycle takes two clock cycles to transfer one byte of data from the device to the memory. What is the approximate speedup when the DMA controller based design is used in place of the interrupt driven program based input-output?
What happen when an interrupt occurs in between CPU executing a program?
If, f: A → B and g: B → C. Then which of the following statements are true: 1. f o g exists and it is a function on B. 2. g o f exists and it is function from A to C. 3. f o g does not exists. 4. g o f does not exists.
If the processor is executing the main program that calls a subroutine, then after executing the main program up to the CALL instruction, the control will be transferred to