Bissoy.com
Doctors Medicines MCQs Q&A

How often does a RIPv1 router broadcast its routing table by default?

How often does a RIPv1 router broadcast its routing table by default? Correct Answer Every 30 seconds

RIPv1 router broadcasts its routing table every 30 seconds by default. The broadcasted routing table can be used by other routers to find the shortest path among the network devices.

Related Questions

Consider a computer network using the distance vector routing algorithm in its network layer. The partial topology of the network is as shown below. The objective is to find the shortest-cost path from the router R to routers P and Q. Assume that R does not initially know the shortest routes to P and Q. Assume that R has three neighbouring routers denoted as X, Y, and Z. During one iteration, R measures its distance to its neighbours X, Y, and Z as 3, 2, and 5, respectively. Router R gets routing vectors from its neighbours that indicate that the distance to router P from routers X, Y, and Z are 7, 6, and 5, respectively. The routing vector also indicates that the distance to router Q from routers X, Y, and Z are 4, 6, and 8, respectively. Which of the following statement(s) is/are correct with respect to the new routing table of R, after updation during this iteration ? 
Which statement is true regarding classless routing protocols?
1. The use of discontiguous networks is not allowed.
2. The use of variable length subnet masks is permitted.
3. RIPv1 is a classless routing protocol.
4. IGRP supports classless routing within the same autonomous system.
5. RIPv2 supports classless routing.
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default
You get a call from a network administrator who tells you that he typed the following into his router:
Router (config) #router ospf 1Router (config-router) #network 10.0.0.0 255.0.0.0 area 0
He tells you he still can't see any routes in the routing table. What configuration error did the administrator make?
Consider the following statements about the functionality of an IP based router. I. A router does not modify the IP packets during forwarding. II. It is not necessary for a router to implement any routing protocol. III. A router should reassemble IP fragments if the MTU of the outgoing link is larger than the size of the incoming IP packet. Which of the above statements is/are TRUE?
A group of 2m - 1 routers are interconnected in a centralized binary tree, with router at each tree node. Router I communicate with router J by sending a message to the root of the tree. The root then sends the message back down to J. Then find the mean router-router path length.
Which two of the following are true regarding the distance-vector and link-state routing protocols?
1. Link state sends its complete routing table out all active interfaces on periodic time intervals.
2. Distance vector sends its complete routing table out all active interfaces on periodic time intervals.
3. Link state sends updates containing the state of its own links to all routers in the internetwork.
4. Distance vector sends updates containing the state of its own links to all routers in the internetwork.
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Consider routing table of an organization’s router shown below: Subnet Number  Subnet Mask Next Hop 12.20.164.0 255.255.252.0 R1 12.20.170.0 255.255.254.0 R2 12.20.168.0  255.255.254.0  Interface 0 12.20.166.0 255.255.254.0 Interface 1  default   R3 Which of the following prefixes in CIDR notation can be collectively used to correctly aggregate all of the subnets in the routing table?
An OSPF router receives an LSA, the router checks its sequence number, and this number matches the sequence number of the LSA that the receiving router already has. What does the receiving router do with the LSA?