Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Which of the following is usually provided with an uncontrolled spillway and an uncontrolled orifice type sluiceway?
When device A has a cable that plugs into device B, and device B has a cable that plugs into device C and device C plugs into a port on the computer, this arrangement is called a _________
Which of the following are true? A. Desktop computer is a general-purpose computer made up of a separate monitor, keyboard, mouse and processor unit B. Laptop is where monitor, keyboard, pointing device, processor unit are combined in a single device C. Tablet is a device with a touch screen; which has a virtual keyboard which uses touch screen technology D. Smart Watch is a device that uses CRT technology so that the screen can bend around the wrist E. Mainframe computer runs small application where small data need to be processed Choose the correct answer from the options given below:
We describe a protocol of input device communication below: i) Each device has a distinct address. ii) The BUS controller scans each device in a sequence of increasing address value to determine if the entity wishes to communicate iii) The device ready to communicate leaves its data in the I/O register iv) The data is picked up and the controller moves to the step a Identify the form of communication best describes the I/O mode amongst the following.
Prashant bought a device from an online store for Rs. 22000, but it was faulty so he returned it, the company accepts a return after deducting 10%. He saw the same device at a discounted price of Rs. 19000, he again ordered the same device, again it was found faulty, he makes a return, the company takes the return after deducting 12%. The amount of money he lost in this whole transaction is what percent of the cost of the device he bought initially?
On a non-pipelined sequential processor, a program segment, which is a part of the interrupt service routine, is given to transfer 500 bytes from an I/O device to memory.     Initialize the address register     Initialize the count to 500 LOOP: Load a byte from device     Store in memory at address given by address register     Increment the address register     Decrement the count     If count! = 0 go to LOOP Assume that each statement in this program is equivalent to a machine instruction which takes one clock cycle to execute if it is a non-load/store instruction. The load-store instructions take two clock cycles to execute. The designer of the system also has an alternate approach of using the DMA controller to implement the same transfer. The DMA controller requires 20 clock cycles for initialization and other overheads. Each DMA transfer cycle takes two clock cycles to transfer one byte of data from the device to the memory. What is the approximate speedup when the DMA controller based design is used in place of the interrupt driven program based input-output?
A device rearranges numbers step by step in a particular order according to a set of rules. The device stops when the final result is obtained. Step V is the final for this device. Input: 86 17 35 03 20 99 64 08 Step I: 99 86 17 35 03 20 64 08 Step II: 99 86 64 17 35 03 20 08 Step III: 99 86 64 35 17 03 20 08 Step IV: 99 86 64 35 20 17 03 08 Step V: 99 86 64 35 20 17 08 03 Study the above arrangement carefully and answer this question. Which one of the following would be the last step for the input below? Input: 02 30 40 20 11 08 
A legislation which confers on the executive or administrative authority an unguided and uncontrolled discretionary power in the matter of application of law violates which one of the following Articles of the Constitution of India?
Which of the following represents examples of an IT input device, output device and storage device respectively ?
Consider the following statements (a) BJT is a current controlled device with high input impedance and high gain band width (b) FET is a voltage- controlled device with high input impedance and low gain bandwidth (c) UJT is a negative resistance device and can be used as an oscillator (d) FET and UJT can be used for amplification Which of the above statements are correct