Computer_all over the world at the moment,

A is using
B has used
C has been using
D is being used

Correct Answer: is being used

Hints: - মূলত বাক্যটি Active voice এ people are using computer ছিল।সেহেতু বাক্যটি passive voice এ লেখা সেহেতু computer is being used হবে।
Bissoy MCQ
#English #পিএসসি ও অন্যান্য নিয়োগ পরীক্ষা #মাধ্যমিক ও উচ্চ মাধ্যমিক শিক্ষা অধিদপ্তর ।। কম্পিউটার মুদ্রাক্ষরিক (12-05-2023)

Related Questions

When a shaft is subjected to combined twisting moment (T) and bending moment (M), then the equivalent twisting moment is equal to
A $$\frac{1}{2}\sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
B $$\sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
C $$\frac{1}{2}\left( {{\text{M}} + \sqrt {{{\text{M}}^2} + {{\text{T}}^2}} } \right)$$
D $${\text{M}} + \sqrt {{{\text{M}}^2} + {{\text{T}}^2}} $$
A beam supporting a uniformly distributed load over its entire length L is pinned at one end and passes over a roller support at a distance x from the other end . The value of x such that the greatest bending moment in the beam is as small as possible, will be
A 0.293L
B 0.330L
C 0.111L
D 0.125L
For a given stress, the ratio of moment of resistance of a beam of square cross-section when placed with its two sides horizontal to the moment of resistance with its diagonal horizontal, is
A $$\frac{1}{2}$$
B 1
C $$\frac{1}{{\sqrt 2 }}$$
D $$\sqrt 2 $$
Mass moment of inertia of a thin rod about its one end is ___________ the mass moment of inertia of the same rod about its mid-point
A Same as
B Twice
C Thrice
D Four times
The yield moment of a cross section is defined as the moment that will just produce the yield stress in
A The outer most fibre of the section
B The inner most fibre of the section
C The neutral fibre of the section
D The fibre everywhere
If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than
A $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
B $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} + \frac{{2{\text{D}}}}{3}} \right)^2}$$
C $$\frac{{{\text{WL}}}}{{10}}{\left( {{\text{L}} - \frac{{2{\text{D}}}}{3}} \right)^2}$$
D $$\frac{{{\text{WL}}}}{{12}}{\left( {{\text{L}} - \frac{{\text{D}}}{3}} \right)^2}$$
In moment resistant connections, the moment resistance of riveted connection depends upon
A Shear in rivets
B Compression in rivets
C Tension in rivets
D Strength of rivets in bearing
The ratio of the moment of inertia of a rectangle about its centroidal axis to the moment of inertia about its base, is
A $$\frac{1}{4}$$
B $$\frac{1}{2}$$
C $$\frac{3}{4}$$
D $$2$$
A rectangular magnet of magnetic moment M is cut into two piece of same length, the magnetic moment of each piece will be
A M
B $$\frac{{\text{M}}}{2}$$
C 2 M
D $$\frac{{\text{M}}}{4}$$
In order to have a connecting rod equally strong in buckling about X-axis and Y-axis, the moment of inertia about X-axis should be __________ the moment of inertia about Y-axis.
A Equal to
B Twice
C Three times
D Four times

Next steps