Bissoy.com
Doctors Medicines MCQs Q&A

Which of the following is not an intermediate code form ?

Which of the following is not an intermediate code form ? Correct Answer Quadrupules

The correct answer is option 3.

Key Points

  • Intermediate code can be represented in three forms, which are postfix notation, Syntax trees, Three address code.
  • In a compiler, three address code can be implemented as records with fields for operator and operands. There are three such representations, Quadruples, Triples, Indirect triples.

∴ Hence the correct answer is Quadruples.

Related Questions

Consider two shafts connected with two gears as per the following options: 1. One on each shaft 2. Through an intermediate gear mounted on an intermediate shaft, and every shaft having one gear only 3. Through an intermediate gear mounted on an intermediate shaft, with the intermediate shaft having two gears, whereas the other shafts have one gear each Which of the above represent(s) a simple gear train?
Which of the following command options are displayed when you use the Router# show frame-relay ? command?
1. dlci
2. neighbors
3. lmi
4. pvc
5. map
Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
1. show version
2. show protocols
3. show interfaces
4. show controllers
5. show ip interface
To enable EIGRP, which of the following would you use?
1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
2. Router1(config-if)# ipv6 router rip 1
3. Router1(config)# ipv6 router eigrp 10
4. Router1(config-rtr)# no shutdown
5. Router1(config-if)# ipv6 eigrp 10
Which two of the following commands will place network 10.2.3.0/24 into area 0?
1. router eigrp 10
2. router ospf 10
3. network 10.0.0.0
4. network 10.2.3.0 0.0.0.255 area0
5. network 10.2.3.0 0.0.0.255 area 0
Which three commands can be used to check LAN connectivity problems on a router?
1. show interfaces
2. show ip route
3. tracert
4. ping
5. dns lookups
You need to allow one host to be permitted to attach dynamically to each switch interface. Which two commands must you configure on your catalyst switch to meet this policy?
1. Switch (config-if) # ip access-group 10
2. Switch (config-if) # switchport port-security maximum 1
3. Switch (config) # access-list 10 permit ip host 1
4. Switch (config-if) # switchport port-security violation shutdown
5. Switch (config) # mac-address-table secure
Which of the following phases of the compiler is machine independent? A. Intermediate code generation B. Target code generation C. Intermediate code optimization
Consider the following statements:
1. Section 34 of Indian Penal Code requires two persons whereas Section 149 of Indian Penal Code require five persons.
2. Section 34 of Indian Penal Code requires common intention, whereas Section 149 of Indian Penal Code requires common object
3. Section 34 of Indian Penal Code and Section 149 of Indian Penal Code both require presence of a prior consent
4. Section 34 of Indian Penal Code and section 149 of Indian Penal Code. Both create specific offence
Which of the above statements are correct?
Network 206.143.5.0 was assigned to the Acme Company to connect to its ISP. The administrator of Acme would like to configure one router with the commands to access the Internet. Which commands could be configured on the Gateway router to allow Internet access to the entire network?
1. Gateway (config) # ip route 0.0.0.0 0.0.0.0 206.143.5.2
2. Gateway (config) # router rip
3. Gateway (config-router) # network 206.143.5.0
4. Gateway (config-router) # network 206.143.5.0 default