Bissoy.com
Doctors Medicines MCQs Q&A

Which of the following is/are correct with regards to Mohr’s circle? I) It is used to denote shear stress distribution. II) Mohr’s circle can be drawn for a fluid at rest.

Which of the following is/are correct with regards to Mohr’s circle? I) It is used to denote shear stress distribution. II) Mohr’s circle can be drawn for a fluid at rest. Correct Answer only I

Explanation:

Mohr’s circle: The graphical method for expressing the relations developed in this section, called Mohr's circle diagram, is a very effective means of visualizing the stress state at a point and keeping track of the directions of the various components associated with plane stress.

     

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)
Which of the following factors are affecting critical shear stresses? 1. Purity of metals reduces the critical shear stress 2. Surface films greatly enhance the critical shear stress 3. Rise in temperature 4. Rate of deformation and the extent of initial deformation also help in raising the critical shear stress
Which of the following statements is/are true? A: If a circle is formed from a wire, which was initially in the shape of a semi-circle, then ratio of radius of circle and that of semi-circle will be 7: 11. B: If in a semi-circle of radius ‘r’, another semi-circle of radius ‘4r/5’ is drawn, then area of the remaining part of larger semi-circle will be ‘3πr2/5’. C: In a circle of radius ‘r’, if ‘O’ is the center of circle and radii OA and OB are at the angle of 45°, then the length of major arc AB will be ‘7πr/8’.
Consider a circle with centre at C. Let OP, OQ denote respectively the tangents to the circle drawn from a point O outside the circle. Let R be a point on OP and S be a point on OQ such that OR × SQ = OS × RP. Which of the following statement(s) is/are correct? (1) If X is the circle with centre at O and radius OR, and Y is the circle with centre at O and radius OS, then X = Y (2) ∠POC + ∠QCO = 90° Select the correct answer using the code given below.
Shear stress versus shear rate behavior of four different types of fluids (I, II, III and IV) are shown in the figure below.
Basic Principles of Biotechnology mcq question image
Which one of the following options is correct?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The Rheological behaviour of concrete, when represented by shear stress vs rate of shear, is characterized as Where : τ shear stress, Τ0 = (initial) yield value, μ = at-point plastic viscosity, γ̇ = at point rate of shear.
If nominal shear stress $${\tau _{\text{v}}}$$ exceeds the design shear strength of concrete $${\tau _{\text{c}}}$$, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
Which of the following statements are correct? 1. Stress Isobar can be prepared using Boussinesq’s stress distribution theory. 2. Equivalent point load method yields accurate results. 3. Newmark’s method relates the vertical stress with the help of influence chart. 4. Westergaard’s method helps in determination of stress distribution for layered soils. Select the correct answer using the codes given below: