Which one of the following is not a fusion welding process?

Gas welding
Arc welding
Brazing
Resistance welding

LohaHridoy

4 views

2025-01-04 04:42

1 Answers

AhmedNazir

Option 3 : Brazing

Explanation:

Fusion welding:

In this process, the base metal is melted by means of heat.
Often, in fusion welding operations, a filler metal is added to the molten pool to facilitate the process and provide bulk and strength to the joint.
Commonly used fusion welding processes are Arc welding, resistance welding, oxyfuel welding, electron beam welding and Laser beam welding.

[ alt="588b1096e9f1310a69f07b71" src="//storage.googleapis.com/tb-img/production/17/01/588b1096e9f1310a69f07b71.PNG" style="height:344px; width:526px">

4 views Answered 2022-09-04 04:29

Related Questions

Which of the following falls under the category of the fusion or non-pressure welding?

1 Answers 4 Views

A virtual memory system uses FIFO page replacement policy and allocates a fixed number of frames to the process. Consider the following statements M : Increasing the number of page frames allocated to a process sometimes increases the page fault rate N : Some programs do not exhibit locality of reference Which one of the following is true?

1 Answers 4 Views

Consider a process executing on an operating system that uses demand paging. The average time for a memory access in the system is M units if the corresponding memory page is available in memory, and D units if the memory access causes a page fault. It has been experimental measured that the average time taken for a memory access in the process is X units. Which one of the following is the correct expression for the page fault rate experienced by the process?

1 Answers 4 Views

The following are some events that occur after a device controller issues an interrupt while process L is under execution (P) The processor pushes the process status onto the control stack. (Q) The processor finishes the execution of the current instruction. (R) The processor executes the interrupt service routine. (S) The processor pops the process status of from the control stack. (T) The processor loads the new PC value based on the interrupt. Which one of the following is the correct order in which the events above occur?

1 Answers 5 Views

In the following question, the 1st and the last part of the sentence/passage are numbered 1 and 6. The rest of the sentence/ passage is split into four parts and named P, Q, R and S. These four parts are not given in their proper order. Read the sentence/ passage and find out which of the four combinations is correct. 1. Jupiter has 2.5 times more mass than all the other planets of the solar system combined and is 11 times as large as Earth in diameter. P. Jupiter is so large that scientists believe it almost became a star: as the gases and dust contracted to the form the planet, Q. But there was not enough mass available to create the temperature needed to start a fusion reaction such as that of the Sun. R. Thus, Jupiter has been cooling down ever since. S. gravitational forces created tremendous pressure and the temperature inside the core—as high as tens of thousands of degrees. 6. Even so, Jupiter radiates about as much heat as it receives from the Sun.?

1 Answers 4 Views

Two processes X and Y need to access a critical section. Consider the following synchronization construct used by both the processes Process /* other code for process */ while(true) { varP = true; while(varQ == true) { /* Critical Section */ varP = false; } } /* other code for process */ Process /* other code for process */ while(true) { varQ = true; while(varP == true) { /* Critical Section */ varQ = false; } } /* other code for process */ Here, varP and varQ are shared variables and both are initialized to false. Which one of the following statements is true?

1 Answers 5 Views

Which two of the following joining processes are autogenous i. Diffusion welding ii. Electroslag welding iii. Tungsten inert gas welding iv. Friction welding?

1 Answers 5 Views

Which of the following is a type of fusion welding?

1 Answers 4 Views

Which of the following is not a fusion welding process?

1 Answers 4 Views

Which of the following is a non-fusion welding?

1 Answers 4 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)