The heat transfer by conduction through a thick cylinder (Q) is given by (where T₁ = Higher temperature, T₂ = Lower temperature, r₁ = Inside radius, r₂ = Outside radius, l = Length of cylinder, and k = Thermal conductivity)?

Q = [2πlk (T₁ - T₂)]/2.3 log (r₂/r₁)
Q = 2.3 log (r₂/r₁)/[2πlk (T₁ - T₂)]
Q = [2π (T₁ - T₂)]/2.3 lk log (r₂/r₁)
Q = = 2πlk/2.3 (T₁ - T₂) log (r₂/r₁)

LohaHridoy

5 views

2025-01-04 04:42

1 Answers

AhmedNazir

Answer: Option 1

The heat transfer by conduction through a thick cylinder (Q) is given by Q = [2πlk (T₁ - T₂)]/2.3 log (r₂/r₁)where T₁ = Higher temperature, T₂ = Lower temperature, r₁ = Inside radius, r₂ = Outside radius, l = Length of cylinder, and k = Thermal conductivity

5 views Answered 2022-09-01 13:21

Related Questions

When the air is passed through an insulated chamber having sprays of water maintained at a temperature higher than the dew point temperature of entering air but lower than its dry bulb temperature, then the air is said to be?

1 Answers 7 Views

Thermal diffusivity of a substance is given by (where h = Thermal diffusivity, ρ = Density of substance, S = Specific heat, and k = Thermal conductivity)?

1 Answers 6 Views

Reynolds number (RN) is given by (where h = Film coefficient, l = Linear dimension, V = Velocity of fluid, k = Thermal conductivity, t = Temperature, ρ = Density of fluid, cp = Specific heat at constant pressure, and μ = Coefficient of absolute viscosity)?

1 Answers 20 Views

Fourier's law of heat conduction is (where Q = Amount of heat flow through the body in unit time, A = Surface area of heat flow, taken at right angles to the direction of heat flow, dT = Temperature difference on the two faces of the body, dx = Thickness of the body, through which the heat flows, taken along the direction of heat flow, and k = Thermal conductivity of the body)?

1 Answers 4 Views

If p₁, is the pressure of air entering the L.P. cylinder and p₂ is the pressure of air leaving the L.P. cylinder (or inter-cooler pressure), then the ratio of cylinder diameters for a single acting, two stage reciprocating air compressor with complete intercooling is given by (where D₁ = Dia. of L.P. cylinder, and D₂ = Dia. of H.P. cylinder)?

1 Answers 6 Views

The ratio of thermal & electrical conductivity is same for all the metals at the same temperature ; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K)?

1 Answers 7 Views

Fouling factor for a heat exchanger is given by (where, U₁ = heat transfer co-efficient of dirty surface U₂ = heat transfer co-efficient of clean surface)?

1 Answers 9 Views

The variation of thermal conductivity of a metal with temperature is often correlated using an expression of the form K = K₀ + at. where, K is the thermal conductivity and T is the temperature (in °K). The units of 'a' in SI system will be?

1 Answers 5 Views

Arithmetic mean area can be used in heat transfer problem to calculate the heat flow by conduction through a cylinder which is?

1 Answers 5 Views

Thermal conductivity based continuous flue gas analyser makes use of varying thermal conductivity of the constituents of flue gases. Which of the following constituents of flue gases has the maximum thermal conductivity?

1 Answers 5 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)