The diagram which shows the correct crank positions corresponding to the opening and closing of the valves, is known as?

Indicator diagram
Axial force diagram
Valve timing diagram
None of these

LohaHridoy

4 views

2025-01-04 04:42

1 Answers

AhmedNazir

Answer: Option 3

A valve timing diagram is a graphical representation of the opening and closing of the intake and exhaust valve of the engine,

4 views Answered 2022-09-01 13:21

Related Questions

When the primary direct crank of a reciprocating engine makes an angle of $$\theta $$ with the line of stroke, then the secondary direct crank will make an angle of _________ with the line of stroke.?

1 Answers 7 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle $$\theta $$ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, the acceleration of the piston is _________ when the crank OC and connecting rod PC are at right angles to each other.?

1 Answers 5 Views

Ten new television shows appeared during the month of September. Five of the shows were sitcoms, three were hour-long dramas, and two were news-magazine shows. By January, only seven of these new shows were still on the air. Five of the shows that remained were sitcoms.?

1 Answers 4 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle $$\theta $$ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO, if N coincides with O, then?

1 Answers 8 Views

In the below figure, PC is the connecting rod and OC is the crank making an angle θ with the line of stroke PO and rotates with uniform angular velocity at $$\omega $$ rad/s. The Klien's acceleration diagram for determining the acceleration of the piston P is shown by quadrilateral CQNO. The acceleration of the piston P with respect to the crank-pin C is given by?

1 Answers 4 Views

The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)?

1 Answers 5 Views

The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)?

1 Answers 6 Views

The velocity of piston in a reciprocating steam engine is given by (where $$\omega $$ = Angular velocity of crank, r = Radius of crank pin circle, $$\theta $$ = Angle turned by crank from inner dead center and n = Ratio of length of connecting rod to the radius of crank)?

1 Answers 7 Views

The tractive force in a locomotive with two cylinders is given by (where c = Fraction of reciprocating parts per cylinder, m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank and $$\theta $$ = Angle of inclination of crank to the line of stroke)?

1 Answers 6 Views

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm)?

1 Answers 4 Views

এক্সাম দিয়ে মেধা যাচাই করুন

Job Preparation (1125)

Admission (754)

এসএসসি (10)

এইচএসসি (5)