Bissoy.com
Doctors Medicines MCQs Q&A

The variation of temperature inside a wall is shown by three different curves. In which case thermal conductivity least varies with temperature

The variation of temperature inside a wall is shown by three different curves. In which case thermal conductivity least varies with temperature Correct Answer B

In the curve shown, B is not having any variation of thermal conductivity with temperature.

Related Questions

Indifference curves relating to supply of labour have a number of properties some of which are mentioned below
1. Indifference curves are downward slopping
2. Indifference curves are upward slopping
3. Higher indifference curves indicate lower levels of utility
4. Higher indifference curves indicate higher levels of utility
5. Indifference curves do not intersect
6. Indifference curves intersect
7. Indifference curves are concave to the origin
8. Indifference curves are convex to the origin
Which among the following properties are not true?
Consider the following statements about thermal conductivity: 1) Thermal conductivity decreases with increasing molecular weight 2) Thermal conductivity of non-metallic liquids generally decreases with increasing temperature 3) Thermal conductivity of gases and liquids is generally smaller than that of solids Which of the above statements are correct?
Walls of a cubical oven are of thickness l, and they are made of material of thermal conductivity k. The temperature inside the oven is 100°C and the inside heat transfer co-efficient is 3k/l. If the wall temperature on the outside is held at 25°C, what is the inside wall temperature in degree centigrade?
A furnace wall consists of two layers. The inside layer of 450 mm is made of light weight bricks of thermal conductivity IW/m.K and outside layer of 900 mm is made of refractory of thermal conductivity 2W/m.K. The hot face of the inside layer is at temperature 1300 K and the cold face of the outer layer is at 400 K. The temperature at the interface between the two layers is . . . . . . . . K.
The heat flux (from outside to inside) across an insulating wall with thermal conductivity, K = 0.04 W/m.°K and thickness 0.16 m is 10 W/m2. The temperature of the inside wall is -5°C. The outside wall temperature is
The temperature variation of a thick brick wall during periodic heating or cooling follows a sinusoidal waveform. During a period of 24 hours, the surface temperature ranges from 25 degree Celsius to 75 degree Celsius. Workout the time lag of the temperature wave corresponding to a point located at 25 cm from the wall surface. Thermo-physical properties of the wall material are; thermal conductivity = 0.62 W/m K; specific heat = 450 J/kg K and density = 1620 kg/m3
A large plane wall, 40 cm thick and 8 m2 area, is heated from one side and temperature distribution at a certain time instant is approximately prescribed by the relation T = 80 – 60 x +12 x2 + 25 x3 – 20 x4 Where temperature t is in degree Celsius and the distance x in meters. Make calculations for heat energy stored in the wall in unit time. For wall material: Thermal conductivity = 6 W/m K and thermal diffusivity = 0.02 m2/hr.
A plane wall of thickness δ has its surfaces maintained at temperatures T1 and T2. The wall is made of a material whose thermal conductivity varies with temperature according to the relation k = k0 T2. Find the expression to work out the steady state heat conduction through the wall?
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
A furnace wall is made of three materials (I, II and III) of equal thickness and having thermal conductivity k1 k2 and k3 respectively. The steady state temperature profile inside each material is shown in the figure. Thermal conductivities of the materials will vary as
Miscellaneous in Metallurgy mcq question image