Bissoy.com
Doctors Medicines MCQs Q&A

When we compare the half bridge converter and full bridge converter 1. The maximum collector current of a full bridge is only double that of the half bridge 2. Full bridge uses 4-power switches instead of 2, as in the double bridge. 3. Output power of a full bridge is twice that of a half bridge with the same input voltage and current. When of the above statements are correct?

When we compare the half bridge converter and full bridge converter 1. The maximum collector current of a full bridge is only double that of the half bridge 2. Full bridge uses 4-power switches instead of 2, as in the double bridge. 3. Output power of a full bridge is twice that of a half bridge with the same input voltage and current. When of the above statements are correct? Correct Answer 2 and 3 only

A full-bridge converter uses 4 power switches and a half-bridge converter uses 2 power switches as shown below.

Single-phase Half wave Converter Drives:

An SEDC motor, fed through a single phase half wave converter as shown below.

[ alt="F1 Shraddha Nakshatra 31.12.2021. D7" src="//storage.googleapis.com/tb-img/production/21/12/F1_Shraddha_Nakshatra_31.12.2021._D7.png" style=" height: 225px; width: 496px;">

Single-phase Full wave Converter Drives:

Circuit and waveform for single-phase full controlled bridge converter supplying an R-L load with continuous load current are shown below.

[ alt="F1 U.B D.K 27.09.2019 D 7" src="//storage.googleapis.com/tb-img/production/19/09/F1_U.B_D.K_27.09.2019_D%207.png" style="width: 362px; height: 232px;">

Output power of a full bridge is twice that of a half bridge with the same input voltage and current.

Related Questions

Consider the following statements: 1. The voltage developed across the OFF switches of the half-bridge converter is the maximum dc-link voltage. 2. In the full-bridge converter, the voltage across the primary of the transformer is the dc link voltage. 3. The voltage developed across the OFF switches of the full-bridge converter is half the maximum dc-link voltage. Which of the above statements are correct?
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?
1. Each end of the trunk link must be set to the IEEE 802.1e encapsulation.
2. The VTP management domain name of both switches must be set the same.
3. All ports on both the switches must be set as access ports.
4. One of the two switches must be configured as a VTP server.
5. A rollover cable is required to connect the two switches together.
6. A router must be used to forward VTP traffic between VLANs.
In comparing the operation of the half-controlled 2-pulse circuit with that of the fully-controlled circuit, which of the following statements are evident? 1. Since half the thyristors are replaced by diodes, a half-controlled converter costs less than a fully-controlled converter. 2. Due to the freewheeling action with a half-controlled bridge-circuit power factor is improved in half-controlled converters. 3. The AC supply current is more distorted due to its zero periods with the half-controlled circuit, compared to a fully-controlled bridge circuit. Select the correct answer using the code given below :
Consider the following statements regarding the Read Only Memory (ROM): 1. The stored data is lost if the power is removed. 2. It consists of an address decoder with a input lines and a programmable OR array with n output lines. 3. The minterms are ORed through the programmable switches which can be made ON or OFF to select a particular minterm. The programmable switches can be implemented by either bipolar, CMOS, nMOS or pMOS technologies. 4. Mask-programmed ROMs are used in the application where the system requires data to be stored and to be changed during the operation. Which of the above statements are not correct ?
Which of the following statements are correct for an ideal constant voltage source? 1. Its output voltage remains absolutely constant whatever the change in load current. 2. It possesses zero internal resistance so that internal voltage drop in the source is zero. 3. Output voltage is provided by the source would remain constant irrespective of the amount of current drawn from it. 4. Output voltage provided by the source varies with the amount of current drawn from it.
Which of the following statements is/are correct? 1. A system is said to be Finite Impulse Response (FIR), if the output samples of the system depend only on the present input and a finite number of past or previous input samples. 2. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a non-recursive system. 3. If the output of a system y(n) depends only on the present input and past inputs, but not on past outputs, then it is called a recursive system.
A 3 - ϕ CSI used for the speed control of an induction motor is to be realized using MOSFET switches as shown below. Switches S1 to S6 are identical switches. The proper configuration for realizing switches S1 to S6 is
Which among the following is/are most appropriate for introducing the topic "comparison of size of different objects" in class I : a: Observe different objects and compare. b: Measure using non-standard units and compare. c: Measure using standard units and compare. d: Superimpose the objects and compare.
A system provides output yi(t) when xi(t) is applied. If the system is said to be LTI then which of the following properties must satisfy? (i).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) + by2(t) (ii).If the input is x(t – T), then the output must be y (t – T) (iii).If the input is x3 = ax1(t) + bx2(t), then output must be y3(t) = ay1(t) * by2(t) (iv).If the input is x(t – T), then the output must be y(t + T)
Consider the following statements regarding n-channel JFET: 1. The maximum drain current IDSS occurs when gate-to-source voltage VGS = 0 V and drain-to-source voltage VDS ≥ |VP|. (VP is pinch-off voltage). 2. For gate-to-source voltage VGS less than the pinch-off level, the drain current is 0 A. 3. For all levels of VGS between 0 V and the pinch-off level, the current ID will range between IDSS and 0 A, respectively. which of the above statements are correct ?