Bissoy.com
Doctors Medicines MCQs Q&A

Why is multi-staging in centrifugal pumps used?

Why is multi-staging in centrifugal pumps used? Correct Answer For high head

Explanation:

  • Multistage centrifugal pumps have multiple liquid chambers (or stages) that are connected in series.
  • Fluid enters the first chamber at suction line pressure and leaves at some elevated pressure.
  • Upon leaving the first stage, the fluid enters the second stage where the pressure is increased further.

Important Points

  • Single-stage: In a single-stage pump, only one impeller is used on the shaft.
  • Multi-stage: In a multi-stage pump, more than one impeller is used on the same shaft and enclosed in the same casing. It is used to raise a high head.

Related Questions

Cconsider the following statements: 1. Pumps used in series are generally of the centrifugal type. 2. Centrifugal pumps, though yielding comparatively smaller discharges than axial flow pumps, yield higher heads (at each stage) compared to axial flow pumps. Which of the above statements is/are correct?
With reference to solar water pumps, consider the following statements: 1. Solar power can be used for running surface pumps and not for submersible pumps. 2. Solar power can be used for running centrifugal pumps and not the ones with piston. Which of the statements given above is/are correct?
Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
A, B and C are three small pumps fitted to a tank. D is a large pump fitted to the tank. Pump B is 25% more efficient than A. Pump C is 20% more efficient than B. Pump D is 4/3rd efficient of pump C. All of the pumps are used to fill the tank. What is the ratio of the time taken by pumps A and B to fill the tank together to the time taken by the pumps B and D to fill the tank together?
A, B and C are 3 small pumps fitted to a tank. D is a large pump fitted to the tank. B is 50% more efficient than A. C is 33.33% more efficient than B. D is 50% more efficient than C. All of the pumps are used to fill the tank. Find the ratio of the time taken by all the pumps to fill the tank when pump D is used to empty the tank and other are used to fill the tank to the time taken when all are used to fill the tank?
Which of the following statements about airlift pumps are correct? Statement 1: In airlift pumps, the air is introduced above a liquid in pressure level and that pressure is used to discharge the liquid. Statement 2: Airlift pumps are used to convey powders in fluidized form.
2 large and 1 small pumps can fill a water tank in 4 hours. 1 large and 3 small pumps can also fill the same water tank in 4 hours . How many hours will it take for 3 large 4 small pumps to fill the tank?
2 large and 1 small pumps can fill a water tank in 4 hours. One large and 3 small pumps can also fill the same water tank in 4 hours. how many hours will it take for 3 large and 4 small pumps to fill the tank?
The cost of manufacturing x water pumps is Tk.9000+400x. The amount received by selling these x water pumps is Tk. 500x. What is the least number of water pumps that must be manufactured and sold so that that the amount recieved is at least equal to the manufacturing cost ?
Consider the following advantages of rotary pumps compared to reciprocating pumps: 1. Steady discharge which increases with decrease in head 2. Suitable for handling fluids with suspended solid particles 3. Less bulky than positive displacement pumps 4. Can be started with open delivery with least load Which of the above advantages are correct?