Bissoy.com
Doctors Medicines MCQs Q&A

Who proposed the method of tension coefficient?

Who proposed the method of tension coefficient? Correct Answer R.V. Southwell

Explanation:

Tension coefficient Method:

  • Prof. R.V. Southwell introduces the Tension Coefficient Method. It is a systematic presentation of the method of joints. 
  • This is especially useful for space frames. This method is valid for a perfect frame.
  • The tension coefficient method is also used for the analysis of trusses.

The Tension Coefficient for a member of a frame is defined as the pull or tension in that member divided by its length. 

t = T/L

t= Tension coefficient for the member 

T= Pull in member 

L= Length of the member

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
According to the International Commission on Education for the Twenty-first Century headed by Jacques Delors, which of the following main tensions will be witnessed during the 21st century ? A. The tension between the global and the local B. The tension between tradition and modernity C. The tension between the spiritual and the material D. The tension between the poor and the rich E. The tension between the developed and the developing societies Choose the correct answer from the options given below:
Determine the correctness or otherwise of the following Assertion (a) and Reason (r).
Assertion: During rolling, front tension and (or) back tension are (is) employed to decrease rolling load.
Reason: Roll pressure decreases due to lowering of flow stress as a result of front tension/back tension.
Determine the pan evaporation from the following data using the Christiansen method. Extra-terrestrial radiation in cm = 47.3cm Coefficient of temperature(Ct) = 1.403 Coefficient for wind velocity (Cw)= 1.2 Coefficient for relative humidity (Ch) = 1 Coefficient for percent of possible sunshine(Cs) = 1.073 Coefficient of elevation(Ce) = 1.014
Which of the following statements are true? a. The correlation coefficient is dependent on the choice of both origin and scale observations. b. The correlation coefficient is dependent on the units of measurements. c. The coefficient of correlation is the square root of the coefficient of determination. d. The zero value of the correlation coefficient cannot estimate the value of the dependent variable.
Which of the following statements are true?
1. The coefficient of rank correlation has the same limits as the Karl Pearson's coefficient of correlation.
2. The coefficient of correlation is independent of the change of origin but not of scale.
3. The covariance between $$X$$ and $$Y$$ is defined as $$\frac{{\sum {xy} }}{n}$$ where, $$x = \left( {X - \overline X } \right),y = \left( {Y - \overline Y } \right)$$      and $$n = $$ no. of paired observations.
4. $${b_{xy}}$$ is called regression coefficient of $$X$$ variable on $$Y$$ variable.
5. If $${b_{xy}}$$ is 0.4 and $${b_{yx}}$$ is 1.6, coefficient of determination would be 0.8.
Select the correct answer:
When the belt is stationary, it is subjected to some tension known as initial tension. The value of this tension is equal to the
Consider the following statements related to design of tension members with single structural shapes and plates: 1. The common single structural shapes are angle sections, tee sections, and channel sections. 2. Single angles are not used for bracing, for light truss tension members. 3. Occasionally, I sections are also used as tension members as they have more rigidity. Which of the above statements are correct?
When the belt is stationary, it is subjected to some tension, known as initial tension. The value of this tension is equal to the
Consider the following statements.
1. Surface tension of liquid depends on length but not on the area, like the elastic property.
2. SI unit of surface tension is N/m.
3. Surface tension is a scalar quantity because it has no specific direction for a given liquid.
Which of the statement(s) given above is/are correct?