Bissoy.com
Doctors Medicines MCQs Q&A

The electrolyte used in lead - acid battery is

The electrolyte used in lead - acid battery is Correct Answer Sulphuric acid

  • The lead - acid battery is an electrochemical device for converting electrical energy into chemical energy and vice versa
  • The main purpose of the battery is to store electrical energy in the form of chemical energy
  • It provides a supply of current for operating various electrical accessories, when the engine is not running
  • When the engine is running it gets electric supply from the dynamo/alternator
  • It is also known as accumulator and storage battery
  • A solution of sulphuric acid and distilled water is used in the Lead - acid battery as electrolyte

Related Questions

Which of the following are the active materials of a lead-acid cell? 1) Lead Peroxide (PbO2) for positive plate 2) Sponge Lead (Pb) for negative plate 3) Concentrated Sulphuric acid (H2SO4) as electrolyte 4) Dilute Sulphuric acid (H2SO4) as electrolyte
If the first two statements are true, the third statement is :
I. Battery X lasts longer than Battery Y.
II. Battery Y doesn't last as long as Battery Z.
III. Battery Z lasts longer than Battery X.
In a batch process, the reaction takes place in the presence of an acid medium. The acid is drained from the reaction vessel at the rate of 15ml/s as a result of the density difference of the acid from the reacting component. To avoid wastage of acid, it is recycled to an acid tank which has 1000 L capacity. The acid drained from the reaction vessel, picks up 50 g/L solids from the reactor. Acid is fed once again to the process from acid tank. When the process is started, the acid is almost pure in the tank as a result of filtration. As the reaction proceeds, acid in the tank gets more and more contaminated with the solids. The concentration of the solids should not exceed 100 g/L from the process point of view. The batch time is 16h. Estimate whether the concentration of the solids will exceed 100g/L during the batch reaction.
Consider the following statements: 1. A solid-state battery has a higher energy density than a Lithium-ion battery that uses liquid electrolyte solution. 2. A solid-state battery is cost-effective as compared to a Lithium-ion battery. Which of the statements given above is/are correct?
In case of an automobile battery, following are the reasons which will cause a defect of
1. Very high charging rate
2. High specific gravity of electrolyte
3. Freezing of electrolyte
4. Improper level of electrolyte
5. Mechanical damage due to rough handling or not fixed in the vehicle
Consider the following materials: 1. Lead peroxide 2. Sponge lead 3. Dilute sulphuric acid Which of the above are active materials of a lead-acid battery?
Which of the following option about secondary cells is/are correct? It consists of a lead anode and a grid of lead packed with lead dioxide (PbO2 ) as a cathode.  A 58% solution of sulphuric acid is used as an electrolyte.
What is the percentage of acid and water present in the electrolyte of a lead-acid battery in a fully charged condition?
Given below are four jumbled sentences. Out of the given options pick the one that gives their correct order. A. You’ve probably noticed, with great disappointment, that the battery doesn’t seem to last as long as it did when it was brand new. B. Partial charging is just fine for lithium-ion batteries and can actually have some positive benefits for cell longevity. C. Smartphone users are forever in search of longer battery life, but unfortunately, battery capacity inevitably declines with age. D. However, one thing you can do to prolong the life of your battery and handset is partial charging.
A three-phase full converter charges a battery from a three-phase supply of 230 V. The battery emf is 200 V and the internal resistance of the battery is 0.5 Ω. Find the value of the continuous current which is flowing through the battery if its terminal voltage is 210 V