Bissoy.com
Doctors Medicines MCQs Q&A

Address Variable রাখা যায় কোনটিতে?

Address Variable রাখা যায় কোনটিতে? Correct Answer pointer

Related Questions

Ecu/cu2+0=-0.34V এবং EFe/Fe2+0=-0.44V হলে, i) তামার পাত্রে FeSO4 দ্রবন রাখা যায়। ii) তামার পাত্রে FeSO4 দ্রবন রাখা যায় না। iii) লৌহ পাত্রে CuSO4 দ্রবণ রাখা যায়। iv) লৌহ পাত্রে CuSO4 দ্রবণ রাখা যায় না। উল্লিখিত উক্তিসমূহের জন্য নিচের কোন উত্তরটি সঠিক?
Which of the following statements is/are correct? 1. An address generated by the CPU is commonly referred to as a physical address. 2. An address seen by the memory unit is commonly referred to as a logical address. 3. The run-time mapping from virtual to physical address is done by the memory management unit (MMU). Select the correct answer using the code given below.
Which two statements describe the IP address 10.16.3.65/23?
1. The subnet address is 10.16.3.0 255.255.254.0.
2. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
3. The last valid host address in the subnet is 10.16.2.254 255.255.254.0.
4. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
Statement I The product of coefficient of correlation, standard deviation of variable 'X' and Standard deviation of variable 'Y' gives the measure of covariance between X and Y variables.
Statement II The product of coefficient of correlation between X and Y variables and the ratio between standard deviation of X variable to standard deviation of Y variable measures the slope of the regression line of X on Y variable.
On a non-pipelined sequential processor, a program segment, which is a part of the interrupt service routine, is given to transfer 500 bytes from an I/O device to memory.     Initialize the address register     Initialize the count to 500 LOOP: Load a byte from device     Store in memory at address given by address register     Increment the address register     Decrement the count     If count! = 0 go to LOOP Assume that each statement in this program is equivalent to a machine instruction which takes one clock cycle to execute if it is a non-load/store instruction. The load-store instructions take two clock cycles to execute. The designer of the system also has an alternate approach of using the DMA controller to implement the same transfer. The DMA controller requires 20 clock cycles for initialization and other overheads. Each DMA transfer cycle takes two clock cycles to transfer one byte of data from the device to the memory. What is the approximate speedup when the DMA controller based design is used in place of the interrupt driven program based input-output?
In a class B subnet, we know the IP address of one host and the mask as given below: IP address = 125.134.112.66 Mask = 255.255.224.0 What is the first address (Network address)?
Consider the following two statements. S1 : Destination MAC address of an ARP reply is a broadcast address. S2 : Destination MAC address of an ARP request is a broadcast address. Which one of the following choices is correct?
You have an IP address of 172.16.13.5 with a 255.255.255.128 subnet mask. What is your class of address, subnet address, and broadcast address?
Which fields are contained within an IEEE Ethernet frame header?
1. Source and destination MAC address
2. Source and destination network address
3. Source and destination MAC address and source and destination network address
4. FCS field
Which statement(s) about IPv4 and IPv6 addresses are true?1. An IPv6 address is 32 bits long, represented in hexidecimal.2. An IPv6 address is 128 bits long, represented in decimal.3. An IPv4 address is 32 bits long, represented in decimal.4. An IPv6 address is 128 bits long, represented in hexidecimal.