Related Questions

Reciprocating pumps are no more to be seen in industrial applications (in comparison to centrifugal pumps) because of
A High initial and maintenance cost
B Lower discharge
C Lower speed of operation
D Necessity of air vessel
A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump
A Develops a lower head
B Capacity is reduced
C Requires more power
D All of the above
Reciprocating pumps compared to centrifugal pumps
A Deliver liquid at uniform pressure
B Can handle slurries more efficiently
C Are not subject to air binding
D Can be operated with delivery valve closed
Centrifugal pumps as compared to reciprocating pumps
A Run at a lower speed for the same discharge
B Do not need priming
C Deliver fluid with pulsating/fluctuating discharge
D Can be run with discharge line valve closed for a short interval
একটি পানিপূর্ণ কুয়ার গভীরতা 20m ও ব্যাস 2 m. কুয়াটিকে পানি শূণ্য করার জন্য 5 HP এর একটি পাম্প লাগানো হল। অর্ধেক পানি তোলার পর পাম্পটি নষ্ট হয়ে গেল। বাকি পানি তোলার জন্য একই ক্ষমতা সম্পন্ন আর একটি পাম্প লাগানো হল। প্রথম পাম্প দ্বারা সম্পাদিত কাজের পরিমান নির্ণয় কর।(The depth and diameter of a water filled well are 20 m and 2 m respectively. An engine of 5 HP is attached to pump out the water. The pump was ruined after emptying half of the water. Then another pump of same capacity was attached to pump out rest of the water. Determine the work done by first pump.) 
A 2.54 × 104 J
B 1.44 × 104 J
C 2.34×104 J
D 1.54 × 104 J
E 1.54 ×104 J
By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. The saving in case of a double acting reciprocating pump is
A 39.2%
B 48.8%
C 84.8%
D 88.4%
By fitting an air vessel to the reciprocating pump, there is always a saving of work done and subsequently saving of power. This saving in case of a single acting reciprocating pump is
A 39.2%
B 48.8%
C 84.8%
D 88.4%
The primary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)
A $${\text{m}}{\omega ^2}{\text{r}}\sin \theta $$
B $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
C $${\text{m}}{\omega ^2}{\text{r}}\frac{{\sin 2\theta }}{{\text{n}}}$$
D $${\text{m}}{\omega ^2}{\text{r}}\frac{{\cos2\theta }}{{\text{n}}}$$
The secondary unbalanced force due to inertia of reciprocating parts in a reciprocating engine is given by (where m = Mass of reciprocating parts, $$\omega $$ = Angular speed of crank, r = Radius of crank, $$\theta $$ = Angle of inclination of crank with the line of stroke and n = Ratio of the length of connecting rod to radius of crank)
A $${\text{m}}{\omega ^2}{\text{r}}\sin \theta $$
B $${\text{m}}{\omega ^2}{\text{r}}\cos \theta $$
C $${\text{m}}{\omega ^2}{\text{r}}\frac{{\sin 2\theta }}{{\text{n}}}$$
D $${\text{m}}{\omega ^2}{\text{r}}\frac{{\cos2\theta }}{{\text{n}}}$$
Working alone, pump A can empty a pool in 3 hours. Working alone, pump B can empty the same pool in 2 hours. Working together, how many minutes will it take pump A and pump B to empty the pool?
A 72
B 75
C 84
D 96

Next steps