Related Questions

3/4th of square were taken to form shape A and the rest was made to form shape B. Shape A was divided into four equal squares (Shape C), what will be the ratio of the one shape C to one shape B.
A 1:4
B 3:16
C 1:2
D 3:4
The maximum shear stress (q) in concrete of a reinforced cement concrete beam is
A $$\frac{{{\text{Shear force}}}}{{{\text{Lever arm}} \times {\text{Width}}}}$$
B $$\frac{{{\text{Lever arm}}}}{{{\text{Shear force}} \times {\text{Width}}}}$$
C $$\frac{{{\text{Width}}}}{{{\text{Lever arm}} \times {\text{Shear force}}}}$$
D $$\frac{{{\text{Shear force}} \times {\text{Width}}}}{{{\text{Lever arm}}}}$$
The strain energy stored in a body due to shear stress, is (where $$\tau $$ = Shear stress, C = Shear modulus and V = Volume of the body)
A $$\frac{{\tau {\text{V}}}}{{2{\text{C}}}}$$
B $$\frac{{2{\text{C}}}}{{\tau {\text{V}}}}$$
C $$\frac{{{\tau ^2}{\text{V}}}}{{2{\text{C}}}}$$
D $$\frac{{2{\text{C}}}}{{{\tau ^2}{\text{V}}}}$$
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
When a body is subjected to a direct tensile stress ($${\sigma _{\text{x}}}$$) in one plane accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), the maximum shear stress is
A $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{{{\sigma _{\text{x}}}}}{2} - \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
C $$\frac{{{\sigma _{\text{x}}}}}{2} + \frac{1}{2}\sqrt {\sigma _{\text{x}}^2 - 4\tau _{{\text{xy}}}^2} $$
D $$\frac{1}{2}\sqrt {\sigma _{\text{x}}^2 + 4\tau _{{\text{xy}}}^2} $$
According to maximum shear stress failure criterion, yielding in material occurs, when the maximum shear stress is equal to __________ times the yield stress.
A 0.5
B 2
C $$\sqrt 2 $$
D $$\sqrt {\frac{3}{2}} $$
The maximum shear stress developed in a beam of circular section is __________ the average shear stress.
A Equal to
B $$\frac{4}{3}$$ times
C 1.5 times
D Twice
The maximum shear stress developed in a beam of rectangular section is __________ the average shear stress.
A Equal to
B $$\frac{4}{3}$$ times
C 1.5 times
D Twice
In a singly reinforced beam, if the permissible stress in concrete reaches earlier than that in steel, the beam section is called
A Under-reinforced section
B Over reinforced section
C Economic section
D Critical section

Next steps