Bissoy.com
Doctors Medicines MCQs Q&A

For same pulley diameters, center distance, belt speed and belt and pulley materials,

For same pulley diameters, center distance, belt speed and belt and pulley materials, Correct Answer Crossed belt drive transmits more power than open belt drive

Related Questions

The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. Calculate the tension in the rope of pulley C.
What is the distance covered by boat N upstream in 5 hours? Which of the following option is sufficient alone to find the answer? A) Boat M is travelling downstream with 20% more downstream speed of boat N. Speed of boat M in still water is 10% more than the speed of boat N in still water. B) Boat M and Boat N are travelling downstream with speed 33 km/hr and 40 km/hr respectively and speed of boat M is still water is 2 times the speed of stream. C) Speed of boat M in still water is 6 km/hr less then speed of boat N in still water and speed of stream is 10 km/hr. D) Speed of stream is ½ times the speed of boat N in still water and downstream speed of boat M is 44 km/hr. E) Speed of stream is 10 km/hr and ratio of upstream speed of boat M and boat N is 3 : 2 respectively.
Each of the question below consists of a question and three statements number I, II and III given below it. You have to decide whether the data provided in the statement are sufficient to answer the question. If the bus is travelling from Surat to Ahmadabad and a car is travelling from Ahmadabad to Surat, then what is the distance between Surat and Ahmadabad? I. The speed of a car is 40% less than the speed of bus. Bus started at 9 am and car started at 10 am and they meet at 3 pm of the same day. II. After travelling for 1 hour, because of traffic average speed of bus is decreased by 20% and covers distance between Surat to Ahmadabad in 11 hours. Original speed of car is 20% less than original speed of bus and before crossing bus it covered 200 km if starts 1 hour later than bus. After crossing car, bus covers remaining distance in 5 hours. III. Speed of bus is 10 km/hr more than the speed of car and before crossing car ratio of distances covered bus and car in same time was 5 : 4. Time taken by car to cover the distance between Ahmadabad and Surat is 2 hours 15 minutes more than time taken by bus to cover the same distance.
If Rati travels at his usual speed for ‘x’ hours, he covers the same distance as he covered when he travels at a speed 30 km/hr less than usual, but for (x + 3) hours. Which of the following can be determined? (A) If he travels at 20 km/hr less speed than usual, he can cover a distance of 240 km in (x - 1) hours. What is the value of ‘x’? (B) If travels at his usual speed for (t + 2) hours, and at 50% of his usual speed for (t - 2) hours, his average speed for the journey is 68 km/hr. What is his usual speed? (C) His usual speed (in km/hr) is a multiple of 5 between 40 and 50 (both inclusive). If ‘x’ is a whole number, what is his usual speed? (D) If he travels at his usual speed for ‘t’ hours, he covers a distance of 400 km. What is the value of ‘x’?
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. If allowable shear stress in the shaft is 70N/mm² and torsional and bending moments are M=1185000N-mm and m=330000N-mm, find the diameter of the shaft.
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. If bending moment on point B in horizontal plate is M and in vertical plane is m, then the net bending moment at point B is?
The layout of a shaft supported on bearings at A & B is shown. Power is supplied by means of a vertical belt on pulley B which is then transmitted to pulley C carrying a horizontal belt. The angle of wrap is 180’ and coefficient of friction is 0.3. Maximum permissible tension in the rope is 3kN. The radius of pulley at B & C is 300mm and 150mm. Calculate the torque supplied to the shaft.
In a flat belt drive, if the slip between the driver and belt is 1%, between the belt and follower is 3% and driver and follower pulley diameters are equal, then velocity ratio of the drive will be
If the angle of wrap on smaller pulley of diameter 250 mm is 1200 and diameter of larger pulley is twice the diameter of smaller pulley, then the centre distance between the pulleys for an open belt drive is
Questions below followed by two quantities. Find the relation between them. The table shows the distance travelled by five different boats upstream, the speed of the boat in still water and the time taken by them to cover the upstream distance. Boats Upstream distance Speed of boat Time taken  A  240 km  15 km/hr  20 hr  B  150 km  10 km/hr  25 hr  C  350 km  20 km/hr  50 hr  D  96 km  8 km/hr  16 hr  E  126 km  26 km/hr  9 hr   Quantity I: Boat B travel 238 km distance downstream in certain time. How much downstream distance boat D will cover at the same time? Quantity II: Boat E travel 722 km distance downstream in certain time. How much downstream distance boat A will cover at the same time?