In the direct acting shock absorber, on rebound stroke, fluid flows out of the upper part of the cylinder and also

“What is the different between height and radius of solid cylinder?” Which of the following option is sufficient alone to find the answer? A) A solid cylinder is made by melting a solid sphere. The radius of cylinder is 3 times the radius of a circle whose area is 154 sq.m. Height of cylinder is equal to the height of cone whose volume is 2772 cubic meters. B) Area of a rectangle whose longer side is ¾ times the radius of a solid cylinder, is 168 sq.m and, Volume of solid cylinder is 2772 cubic meters and its height is 18 m. C) A metallic cone of radius 15m and height 35m is melted into the solid cylinder of radius equal to the radius of a circle whose area is equal to the area of rectangle whose sides are in the ratio 4 : 3 respectively. D) The curved surface area of the solid cylinder is 3 time the surface area of a sphere of radius 7m and height of cylinder is equal to the height of a metallic cone whose curved surface area is 308 sq.m.

A

Only A and B

B

Only B and C

C

Only B

D

All A, B, C and D

E

None of A, B, C and D

If d=depth of cut in mm, f=feed in mm/stroke, n=stroke/min, l=length of stroke in mm, m= ratio of return stroke time to cutting stroke time, then find the formula for metal removal rate.

A

f*d*l*n*(m+1)

B

f*d*l*n*m

C

f*d*l*n*m/1000

D

none of the mentioned

If p₁, is the pressure of air entering the L.P. cylinder and p₂ is the pressure of air leaving the L.P. cylinder (or inter-cooler pressure), then the ratio of cylinder diameters for a single acting, two stage reciprocating air compressor with complete intercooling is given by (where D₁ = Dia. of L.P. cylinder, and D₂ = Dia. of H.P. cylinder)

A

D₁/D₂ = p₁ p₂

B

D₁/D₂ = p₁/p₂

C

D₁/D₂ = p₂/p₁

D

None of these

If p₁, is the pressure of air entering the L.P. cylinder and p₂ is the pressure of air leaving the L.P. cylinder (or inter-cooler pressure), then the ratio of cylinder diameters for a single acting, two stage reciprocating air compressor with complete intercooling is given by (where D₁ = Diameter of L.P. cylinder and D₂ = Diameter of H.P. cylinder)

A

$$\frac{{{{\text{D}}_1}}}{{{{\text{D}}_2}}} = {{\text{p}}_1}{{\text{p}}_2}$$

B

$$\frac{{{{\text{D}}_1}}}{{{{\text{D}}_2}}} = \frac{{{{\text{p}}_1}}}{{{{\text{p}}_2}}}$$

C

$$\frac{{{{\text{D}}_1}}}{{{{\text{D}}_2}}} = \frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}}$$

D

None of these

Bernoulli's equation for fluid flow is derived following certain assumptions. Out of the assumptions listed below, which set of assumptions is used in derivation of Bernoulli's equation?
1. Fluid flow is frictionless & irrotational
2. Fluid flow is steady
3. Fluid flow is uniform & turbulent
4. Fluid is compressible
5. Fluid is incompressible

A

1, 3, 4

B

2, 4, 5

C

1, 2, 5

D

1, 4, 5

The curved surface area of cylinder A is 8% more than the curved surface area of cylinder B. If the height of cylinder A is 4% less than the height of cylinder B, then the volume of cylinder A is what percentage more/less than the volume of cylinder B?

A

10.5% less

B

10.5% more

C

21.5% less

D

21.5% more

The curved surface area of cylinder X is 45% of the curved surface area of cylinder Y. If the volume of cylinder X is 27% of the volume of cylinder Y, then the height of cylinder X is what percentage of the height of cylinder Y?

A

25%

B

50%

C

75%

D

100%

BBD studies were carried out on a highway pavement at a temperature of 40°C. The rebound deflection was found to be 1.41 mm. what would be the corrected rebound deflection?

A

1.33 mm

B

1.35 mm

C

1.40 mm

D

1.36 mm

In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed

A

10 mm

B

15 mm

C

20 mm

D

25 mm

A hollow cylinder is formed by cutting out a solid cylinder of radius r/k from a solid cylinder of radius r. The height of both solid cylinders was equal. The volume of the hollow cylinder m times the volume of the new solid cylinder. What is the relationship between m and k?

A

k² = m

B

k² = m + 1

C

k² = m - 1

D

k² = 2m

In the direct acting shock absorber, on rebound stroke, fluid flows out of the upper part of the cylinder and also

Related Questions