Bissoy.com
Doctors Medicines MCQs Q&A

If average heat transfer co-efficient is $${{\text{h}}_{\text{a}}}$$ and the local coefficient at the end of the plate is $${{\text{h}}_l}$$ then in case of heat transfer to a fluid flowing over a flat plate, heated over its entire length

If average heat transfer co-efficient is $${{\text{h}}_{\text{a}}}$$ and the local coefficient at the end of the plate is $${{\text{h}}_l}$$ then in case of heat transfer to a fluid flowing over a flat plate, heated over its entire length Correct Answer $${{\text{h}}_{\text{a}}} = 2{{\text{h}}_l}$$

Related Questions

If average heat transfer co-efficient is ha and the local coefficient at the end of the plate is hl then in case of heat transfer to a fluid flowing over a flat plate, heated over its entire length
Experimental results indicate that the local heat transfer coefficient h g for flow over a flat plate with an extremely rough surface is approximated by the relation h x = a x -0.12 Where a is a constant coefficient and x is distance from the leading edge of the plate. What is the relation between this local heat transfer coefficient and the average heat transfer coefficient for a plate of length x?
A stream of air at 100 kPa pressure and 300 K is flowing on the top surface of a thin flat sheet of solid naphthalene of length 0.2 m with a velocity of 20 m/sec. The other data are: Mass diffusivity of naphthalene vapor in air = 6 * 10 –6 m2/sec Kinematic viscosity of air = 1.5 * 10 –5 m2.sc Concentration of naphthalene at the air-solid naphthalene interface = 1 * 10 – 5 kmol/m3 Calculate the overage mass transfer coefficient over the flat plate. Note: For heat transfer over a flat plate, convective heat transfer coefficient for laminar flow can be calculated by the equation. Nu = 0.664 ReL1/2 Pr1/3 you may use analogy between mass and heat transfer.
The average heat transfer co-efficient over the entire length of the plate (ha) and the local heat transfer co-efficient (hL), in case of heat transfer over a flat plate in lminar zone is related as
The average heat transfer co-efficient over the entire length of the plate (ha) and the local heat transfer co-efficient (hL), in case of heat transfer over a flat plate in lminar zone is related as
Ambient air at 20 degree Celsius flows past a flat plate with a sharp leading edge at 3 m/s. The plate is heated uniformly throughout its entire length and is maintained at a surface temperature of 40 degree Celsius. Calculate the local convective heat transfer coefficient. Assume that transition occurs at a critical Reynolds number of 500000
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
Six flats A, B, C, D, E and F are located in two rows of three flats each. The flats in both the rows face each other. Flat D is diagonally opposite to flat C. Flat E is opposite to flat F, which is north facing. Flat C is 2nd to the left of A and both of flats are south facing. Which of the following flats is facing flat B?
Air at 25 degree Celsius approaches a 0.9 m long and 0.6 m wide flat plate with a velocity 4.5 m/s. Let the plate is heated to a surface temperature of 135 degree Celsius. Find local heat transfer coefficient from the leading edge at a distance of 0.5 m
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K