Which of the following is the definition of proportional band of a controller ?

A The range of air output as measured variable varies from maximum to minimum
B The range of measured variables from set value
C The range of measured variables through which the air output changes from maximum to minimum
D Any of the above
E None of the above

Correct Answer: The range of measured variables through which the air output changes from maximum to minimum

Bissoy MCQ
#Electrical Engineering #Electrical Control Systems

Related Questions

Determine the resistance value and tolerance of a resistor that has the following color bands; first band is red, second band is red, third band is orange, and the fourth band is gold
A 220 Ohm, 5%
B 220 Ohm, 10%
C 22,000 Ohm, 5%
D 22, 000 Ohm, 10%
E None of the above
In comparing the United Stares Government’s definition of services with the classical definition, the author suggests that the classical definition is-
A more pragmatic
B more difficult to apply
C less ambiguous
D more arbitrary
In comparing the United States Government in’s definition of the services with the classical definition, the author suggests that the classical definition is-
A More pragmatic
B More difficult to apply
C Less ambiguous
D More arbitrary
সুপরিবাহী পদার্থে Valence Band এবং conduction band-
A আলাদা থাকে
B ওভারল্যাপ থাকে
C অনেক দূরে থাকে
D কোনটিই নয়
The forbidden energy gap between the valence band and conduction band will be least in case of
A Metals
B Semiconductors
C Insulators
D All of the above
A band-pass filter rejects all frequencies within a band between a lower and an upper critical frequency and passes all others.
A True
B False
The bandwidth of C-band satellite frequency band in U.S.
A 500 GHz
B 1000 GHz
C 1000 MHz
D 500 MHz
The current due to electron flow in conduction band is the hole current in valence band.
A Equal to
B Less than
C Greater than
D Any of the above
In a band and block brake, the ratio of tensions on tight side and slack side of the band is (where $$\mu $$ = Coefficient of friction between the blocks and the drum, $$\theta $$ = Semi-angle of each block subtending at the center of drum and n = Number of blocks)
A $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = \mu \theta {\text{n}}$$
B $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 - \mu \tan \theta }}{{1 + \mu \tan \theta }}} \right)^{\text{n}}}$$
C $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\mu \theta } \right)^{\text{n}}}$$
D $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 + \mu \tan \theta }}{{1 - \mu \tan \theta }}} \right)^{\text{n}}}$$
In a band and block brake, the ratio of tensions on the tight and slack sides of band is given by (where $$\mu $$ = Coefficient of friction between the blocks and the drum, $$\theta $$ = Semi-angle of each block subtending at the centre of drum and n = Number of blocks)
A $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_{\text{2}}}}} = \mu \theta \times {\text{n}}$$
B $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\mu \theta } \right)^{\text{n}}}$$
C $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 - \mu \tan \theta }}{{1 + \mu \tan \theta }}} \right)^{\text{n}}}$$
D $$\frac{{{{\text{T}}_1}}}{{{{\text{T}}_2}}} = {\left( {\frac{{1 + \mu \tan \theta }}{{1 - \mu \tan \theta }}} \right)^{\text{n}}}$$

Next steps