During drawing operation, the states of stress in cup would include

A Compressive stress in the flange
B Tensile stress in the wall
C Both (A) and (B)
D None of these

Correct Answer: Both (A) and (B)

The stress in the flange region during the deep drawing process is a combination of radial tensile drawing stress and a tangential compressive stress.
The blank-holder at the top of the workpiece exerts a compressive force at the upper surface of the blank during the drawing process.
Bissoy MCQ
#Mechanical Engineering #Workshop Technology

Related Questions

The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
A Working
B Damaging
C Allowable
D None of these
Federation Cup, World Cup, Allywy International Trophy and Challenge Cup are awarded to winners of -
A Tennis
B Basketball
C Volleyball
D Cricket
An Auto-CAD term that refers to a pre-drawn object which is stored in a drawing file and can be inserted into any other drawing file as needed is a __________.
A Block
B Brick
C Balloon
D None of the above
In order to set drawing limits for a 'C' size architectural drawing the drafter should set the limits to ________.
A 0, 0 and 2, 9
B 0, 0 and 17, 11
C 0, 0 and 18, 24
D 0, 0 and 34, 24
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to _________.
A 0, 0
B 10, 10
C 20, 20
D 30, 30
Often earing defects are found during deep drawing operation, because the
A surface finish of the sheet is poor
B sheet material has been given substantial spring back
C starting sheet has planer anisotropy due to its texture
D starting sheet has normal anisotropy due to its texture
A plate with an elliptical hole in the centre, with semi-major axis (a) perpendicular to the direction of loading and semi-minor axis (b) along the direction of loading, is subjected to a pull P. The maximum stress induced at the edge of the hole is equal to (where $$\sigma $$ = Stress for a plate with no hole i.e. nominal stress)
A $$\sigma \left( {1 + \frac{{\text{b}}}{{2{\text{a}}}}} \right)$$
B $$\sigma \left( {1 + \frac{{2{\text{a}}}}{{\text{b}}}} \right)$$
C $$\sigma \left( {1 + \frac{{\text{b}}}{{3{\text{a}}}}} \right)$$
D $$\sigma \left( {1 + \frac{{3{\text{a}}}}{{\text{b}}}} \right)$$
The maximum stress due to stress concentration in a bar having circular transverse hole, as compared to its static stress without hole will be
A Same in both cases
B 2 times more
C 3 times more
D 4 times more
In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on
A horizontal plane only
B vertical plane only
C both horizontal and vertical planes
D all planes except horizontal and vertical planes
When a body is subjected to biaxial stress i.e. direct stresses ($${\sigma _{\text{x}}}$$) and ($${\sigma _{\text{y}}}$$) in two mutually perpendicular planes accompanied by a simple shear stress ($${\tau _{{\text{xy}}}}$$ ), then maximum shear stress is
A $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
B $$\frac{1}{2}\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + 4\tau _{{\text{xy}}}^2} $$
C $$\sqrt {{{\left( {{\sigma _{\text{x}}} - {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$
D $$\sqrt {{{\left( {{\sigma _{\text{x}}} + {\sigma _{\text{y}}}} \right)}^2} + \tau _{{\text{xy}}}^2} $$

Next steps