Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Statement (I): The Supersaturated expansion in nozzle is a process in which the steam expands beyond the saturated vapour line superheated condition. Statement (II): Steam cannot exist in superheated state when the expansion process in nozzle reaches the saturated vapour line
Consider the following statements: 1. There is no change in temperature when a liquid is being evaporated into vapour 2. Vapour is a mixed phase of liquid and gas in the zone between saturated liquid line and saturated vapour line 3. The saturated dry vapour curve is steeper as compared to saturated liquid curve on a T-s diagram 4. The enthalpy of vaporization decreases with increase in pressure Which of the above statements are correct?
A cylinder of 0.8 m3 in volume contains superheated steam at 70℃ and .4 N/m2 absolute pressure. The superheated steam is compressed to .3 . Find pressure and temperature.
In a laboratory test run, the rate of drying was found to be 0.5 × 10-3 kg/m2.s, when the moisture content reduced from 0.4 to 0.1 on dry basis. The critical moisture content of the material is 0.08 on a dry basis. A tray dryer is used to dry 100 kg (dry basis) of the same material under identical conditions. The surface area of the material is 0.04 m2/kg of dry solid. The time required (in seconds) to reduce the moisture content of the solids from 0.3 to 0.2 (dry basis) is
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. The first full­scale, working steam ­powered tricycle was built by:
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. Cugnot built steam tractors for:
To improve the quality of steam at turbine exit which of the following will be used? 1. Reheat cycle 2. Increase the maximum pressure when maximum and minimum temperatures are fixed 3. Use superheated steam, instead of saturated steam when the maximum and minimum pressures are fixed
The ratio of exit pressure to inlet pressure for maximum mass flow rate per unit area of steam through a nozzle when steam is initially dry saturated is
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. The problem with Trevithick's Puffing Devil was:
Read the passage carefully and choose the best answer to each question out of the four alternatives and click the button corresponding to it. The first working steam­ powered vehicle was designed and most likely built by Ferdinand Verbies, a Flemish member of a Jesuit mission in China around 1672. It was a 65 cm long scale­ model toy for the Chinese Emperor, that was unable to carry a driver or a passenger. It is not known if Verbiest's model was ever built. Nicolas- Joseph Cugnot is widely credited with building the first full­ scale, self ­propelled mechanical vehicle or automobile in about 1769; he also created a steam­ powered tricycle. He constructed two steam tractors for the French Army, one of which is preserved in the French National Conservatory of Arts and Crafts. His inventions were however handicapped by problems of water supply and maintaining steam pressure. In 1801, Richard Trevithick built and demonstrated his Puffing Devil road locomotive, believed by many to be the first demonstration of a steam ­powered road vehicle. It was unable to maintain sufficient steam pressure for long periods. Sentiment against steam ­powered road vehicles led to the Locomotive Acts of 1865. In 1807 Nicephore Niepce and his brother Claude probably created the world's first internal combustion engine which they called Pyreolophore. What is meant by "Sentiment" in the context of the given paragraph?