For perfect intercooling in a two stage compressor

A $$\frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}} = \frac{{{{\text{p}}_3}}}{{{{\text{p}}_2}}}$$
B $$\frac{{{{\text{p}}_1}}}{{{{\text{p}}_3}}} = \frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}}$$
C $${{\text{p}}_1} = {{\text{p}}_3}$$
D $${{\text{p}}_1} = {{\text{p}}_2}{{\text{p}}_3}$$

Correct Answer: $$\frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}} = \frac{{{{\text{p}}_3}}}{{{{\text{p}}_2}}}$$

For perfect intercooling in a two stage compressor $$\frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}} = \frac{{{{\text{p}}_3}}}{{{{\text{p}}_2}}}$$
Bissoy MCQ
#Mechanical Engineering #Compressors #Gas Turbines And Jet Engines

Related Questions

When the temperature of air leaving the inter-cooler, in a two stage compression with inter-cooler, is ________ the original atmospheric air temperature, then the intercooling is known as perfect or complete intercooling.
A Equal to
B Less than
C More than
D None of these
For perfect intercooling in a three stage compressor
A $$\frac{{{{\text{p}}_2}}}{{{{\text{p}}_1}}} = \frac{{{{\text{p}}_3}}}{{{{\text{p}}_2}}} = \frac{{{{\text{p}}_4}}}{{{{\text{p}}_3}}}$$
B $$\frac{{{{\text{p}}_3}}}{{{{\text{p}}_1}}} = \frac{{{{\text{p}}_4}}}{{{{\text{p}}_2}}}$$
C $${{\text{p}}_1}{{\text{p}}_2} = {{\text{p}}_3}{{\text{p}}_4}$$
D $${{\text{p}}_1}{{\text{p}}_3} = {{\text{p}}_2}{{\text{p}}_4}$$
For a two stage compressor, if index of compression for higher stage is greater than index of compression for lower stage, then the optimum pressure as compared to ideal case will
A Increase
B Decrease
C Remain unaffected
D Other factors control it
Which is false statement about advantages of multistage compressor in comparison to single stage compressor?
A Less power requirement
B Better mechanical balance
C Less loss of air due to leakage past the cylinder
D Lower volumetric efficiency
In an axial flow compressor, the ratio of pressure in the rotor blades to the pressure rise in the compressor in one stage is known as
A Work factor
B Slip factor
C Degree of reaction
D Pressure coefficient
The minimum work required for a three stage reciprocating air compressor is ________ the work required for each stage.
A Equal to
B Double
C Three times
D Six times
Axial flow compressor has the following advantage over centrifugal compressor
A Larger air handling ability per unit frontal area
B Higher pressure ratio per stage
C Aerofoil blades are used
D Higher average velocities
In a centrifugal compressor, the flow of air is ________ to the axis of compressor.
A Parallel
B Perpendicular
C Inclined
D None of these
If the flow of air through the compressor is parallel to its axis, then the compressor is
A Reciprocating compressor
B Centrifugal compressor
C Axial flow compressor
D Turbo compressor
For very low pressure and high discharge rate, the compressor used is a/an __________ compressor.
A Axial
B Reciprocating
C Rotary
D None of these

Next steps