Bissoy.com
Doctors Medicines MCQs Q&A

Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be

Two D.C. shunt generators, each with armature resistance of 0.02 ohm and field resistance of 50 ohm run in parallel and supply a total current of 1000 amperes to the load circuit. If their e.m.fs. are 270 V and 265 V, their bus bar voltage will be Correct Answer 267.5 V

Related Questions

A 100KW, 250 V, 400 A, a long shunt compound generator has an armature resistance of 0.025 ohms. There are 1000 shunt fields turns per pole and 3 series field turns per pole. The series field is connected in a such a fashion that positive armature current produces direct-axis MMF which adds to that of the shunt field. Compute the gross MMF at the rated terminal current when shunt field current is 4.7A and speed is 1150 rpm.
Each of the question below consists of a question and three statements number I, II and III given below it. You have to decide whether the data provided in the statement are sufficient to answer the question. If the bus is travelling from Surat to Ahmadabad and a car is travelling from Ahmadabad to Surat, then what is the distance between Surat and Ahmadabad? I. The speed of a car is 40% less than the speed of bus. Bus started at 9 am and car started at 10 am and they meet at 3 pm of the same day. II. After travelling for 1 hour, because of traffic average speed of bus is decreased by 20% and covers distance between Surat to Ahmadabad in 11 hours. Original speed of car is 20% less than original speed of bus and before crossing bus it covered 200 km if starts 1 hour later than bus. After crossing car, bus covers remaining distance in 5 hours. III. Speed of bus is 10 km/hr more than the speed of car and before crossing car ratio of distances covered bus and car in same time was 5 : 4. Time taken by car to cover the distance between Ahmadabad and Surat is 2 hours 15 minutes more than time taken by bus to cover the same distance.
For a given compound DC machine, Net field current obtained from characteristic is equal to 7.5 A, where shunt field current is equal to 5 A, armature current is 505 A, demagnetizing current equal to 0.95 A and shunt field winding of 1000 turns at rated speed of 1000 rpm. What will be the series field turns?
A shunt generator has an induced voltage on open circuit of 127 V. When the machine is on load the terminal voltage is 120 V. The load current if the field resistance be 15 ohm and armature resistance be 15 ohm.
Consider the following statements: In the above figure, the curves pertain to the DC motor A. Speed vs Armature current characteristic of a DC shunt motor B. Torque vs Armature current characteristic of a DC shunt motor C. Speed vs Armature current characteristic of a DC series motor D. Torque vs Armature current characteristic of a DC series motor
Which of the following statements are true? a. As load increases armature current decreases, regardless of excitation. b. For under and over excited motors, power factor tends to approach zero with increase in load c. With normal excitation when load is increased, change in armature current is greater than in power factor which tends to become increasingly leading. d. Both with under and over excitation, change in power factor is greater than in armature current with increase in load.
The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be
A person purchases 10 used generators at Rs. 2,000 each. Accessories of Rs. 5,000 were used to repair and paint the generators. He was able to sell 6 generators at Rs. 2,500 each but incurred a loss of 10% in the whole deal. Find the selling price of each generator and loss percentage on each generator of remaining generators.
Consider the following statements regarding the starting of a dc shunt motor: a. External field resistance should be minimum b. External field resistance should be maximum c. Reduced voltage should be applied to the armature d. Increased voltage should be applied to the armature Which of the above statements are correct?
For a Zener diode shunt regulator, the source current is IS, the Zener diode current is IZ and the load current is IL. The source voltage is VS, Zener voltage is VZ and load voltage is VL. The load resistance is RL. What is the correct option for the safe operation of the diode?