Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Consider the following two C code segment. Y and X are one- and two-dimensional arrays of size n and n × n respectively, where 2 ≤ n ≤ 10. Assume that in both code segments, elements of y are initialized to 0 and each element X[i] [j] of array X is initialized to i + j. Further assume that when stored in main memory all elements of x are in same main memory page frame. Code segment 1:                 //initialize elements of y to 0                 //initialize elements X[i] [j] of X to i+j                       for (i = 0; i < n; i++)                                 Y[i] += X[0] [i]; Code Segment 2:                 //initialize elements of Y to 0                 //initialize elements X[i] [j] of X to i+j                        for (i = 0; i < n; i++)                                 Y[i] += X[i] [0]; Which of the following statements is/are correct? S1: Final contents of array Y will be same in both code segments S2: Elements of array X accessed inside the for loop shown in code segment 1 are contiguous in main memory S3: Elements of array X accessed inside the for loop shown in code segment 2 are contiguous in main memory
A shared variable x, initialized to zero, is operated on by four concurrent processes W, X, Y, Z as follows. Each of the processes W and X reads x from memory, increments by one, stores it to memory, and then terminates. Each of the processes Y and Z reads x from memory, decrements by two, stores it to memory, and then terminates. Each process before reading x invokes the P operation (i.e., wait) on a counting semaphore S and invokes the V operation (i.e., signal) on the semaphore S after storing x to memory. Semaphore S is initialized to two. What is the maximum possible value of x after all processes complete execution?
Each of a set of n processes executes the following code using two semaphores a and b initialized to 1 and 0, respectively. Assume that count is a shared variable initialized to 0 and not used in CODE SECTION P. CODE SECTION P wait (a); count=count+1 ; if (count==n) signal (b) ; signal (a) ; wait (b) ; signal (b) ; CODE SECTION Q What does the code achieve?
A too-large weight initialized on the neural network can lead to vanishing gradient whereas a too-small weight initialized on the neural network can lead to exploding gradient.
A = Area of the largest circle drawn inside a square of side 1 cm. B = Sum of areas of 4 identical (largest possible) circles drawn inside a square of side 1 cm. C = Sum of areas of 9 identical circle (largest possible) drawn inside a square of side 1 cm. D = Sum of area of 16 identical circles (largest possible) drawn inside a square of side 1 cm. Which of the following is TRUE about A, B, C and D?
Your inside locals are not being translated to the inside global addresses. Which of the following commands will show you if your inside globals are allowed to use the NAT pool? ip nat pool Corp 198.18.41.129 198.18.41.134 netmask 255.255.255.248 ip nat inside source list 100 int pool Corp overload
For estimating maximum value of multiple correlation, which of the following conditions should be met ? I. Independent variables should correlate high with the dependent variable. II. The Independent variables should correlate low with one another. Select the correct alternative from the following :
You have an interface on a router with the IP address of 192.168.192.10/29. Including the router interface, how many hosts can have IP addresses on the LAN attached to the router interface?
Just for a simplicity consider a pure substance B. By analogy with the migration of a high-angle grain boundary the net flux of B across the interface will produce an interface velocity v given by____ (Interface mobility is given as M, Molar volume V, and the driving force is given as Δμ)
You are installing a network interface card on a computer with the following configuration: a 5867133 CPU, 16MB or RAM, a 800-MB IDE hard disk, a parallel port configured as LPT1, and a serial port configured as COM1, which is currently used by a mouse. In addition to the IDE host adapter and the video card, the following devices have been installed on the computer's expansion bus: a modem on COM2, a SCSI host adapter for a CD-ROM drive, and a sound card. The SCSI hose adapter is using IRQ 5, and the sound card is using IRQ 11. The network interface card that you are installing supports the following choices for IRQ: 2, 3, 4, 5, 9,10 and 11. Which IRQ(s) could you use for the network interface card without creating an IRQ conflict with another device?