Find the metal removal rate from the given data (in mm*mm*mm/minute). cutting speed(cs) =50 mm/minute, depth of cut(d)=10mm, feed(f)= o.1 mm/revolution.

Which of the following statements are true?
Statement I Big data refers to no precise quantity, but generally refers to data in the range of Petabytes and Exabyte, i.e. billions to trillions of records, all from various sources. Big data is generated much faster. than traditional data in much larger quantities.
Statement II Big data interests industries because they are able to learn more patterns and curious variances than smaller data sets, with the capability to provide valuable insights into consumer behaviour, weather systems, financial market activity, or other phenomena.
Statement III Various departments and product lines use various applications within most organisations and store data in separate datasets. These separate databases may contain similar data, but data from one data base to another is not always consistent. This is called data silo.

A

Both statements I and II

B

Both statements II and III

C

Both statements I and III

D

All of the above

Find the cutting speed from the given data (in mm/minute). metal removal rate(mrr) =50 mm*mm*mm/minute, depth of cut(d)=1mm, feed(f)= o.1 mm/revolution.

A

50

B

500

Find the feed from the given data (in mm/revolution). cutting speed(cs) =50 mm/minute, depth of cut(d)=100mm, metal removal rate(mrr)= 10 mm/revolution.

A

0.2

B

0.02

If d=depth of cut in mm, f=feed in mm/stroke, n=stroke/min, l=length of stroke in mm, m= ratio of return stroke time to cutting stroke time, then find the formula for metal removal rate.

A

f*d*l*n*(m+1)

B

f*d*l*n*m

C

f*d*l*n*m/1000

D

none of the mentioned

Which of the following statements are true/false?
1. A minimum rate of wages for the time spent by employees for the production of output is minimum time rate.
2. Minimum piece rate is the rate based on the quantity of the output employees have produced.
3. The guaranteed time rate is a minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis.
4. A minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis is overtime rate.

A

1, 2, 3 and 4 are true

B

1, 3 are true and 2, 4 are false

C

2, 4 are true and 1, 3 are false

D

3, 4 are true and 2, 1 are false

Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?

A

1 and 2 only

B

1 and 3 only

C

2 and 3 only

D

1, 2 and 3

Flank wear occurs mainly on the 1. Nose part of the cutting tool 2. Front relief face and side relief face of the cutting tool 3. Face of the cutting tool at the shortest distance from the cutting edge Which of the above is/are correct?

A

1 and 2

B

1 and 3

C

2 only

D

1 only

Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image

A

1

B

2

C

3

D

4

Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image

A

1

B

2

C

3

D

4

Choose a figure which would most closely resemble the unfolded form of figure (Z).
Paper Cutting mcq question image

A

1

B

2

C

3

D

4

Find the metal removal rate from the given data (in mmmmmm/minute). cutting speed(cs) =50 mm/minute, depth of cut(d)=10mm, feed(f)= o.1 mm/revolution.

Related Questions