Which is the material used to wound on a wire wound piston?

Which is the material used to wound on a wire wound piston? Correct Answer Steel

In a wire wound piston a band of steel wire under initial tension is put between the piston pin and the oil control ring, thus restricting the expansion of the skirt which is of slip type or cam ground type. The main reason to wire-wound is to avoid piston slap.
Bissoy MCQ

Related Questions

The diameters of a small piston and a large piston of a hydraulic jack are 45 mm and 100 mm respectively.Force of 0.09 kN applied on smaller in size piston. Find load lifted by piston if smaller in size piston is 40 cm above the large piston. The density of fluid is 850 kg/m3
A telephone switchboard 100 pair cable can be made up with either enameled wire or tinned wire. There will be 400 soldered connections. The cost of soldering a connection on the enameled wire will be P 1.65 on the tinned wire, it will be P 1.15. A 100- pair cable made up with enameled wire cost P 0.55 per linear foot and those made up of tinned wire cost P 0.75 per linear foot. Determine the length of cable run in feet so that the cost of each installation would be the same.
An elevator is assembled to raise equipment to a height of 22m. It is estimated that maximum weight of the material to be raised is 4.9kN. It is observed acceleration in such cases is 1.2m/s².10mm diameter wire ropes with fibre core are used. The tensile designation of the wire is 1500.Number of rope wires is assumed to be 2. Calculate the weight of wire if weight of 50m wire is 18kg.
An elevator is assembled to raise equipment to a height of 22m. It is estimated that maximum weight of the material to be raised is 4.9kN. It is observed acceleration in such cases is 1.2m/s².10mm diameter wire ropes with fibre core are used. The tensile designation of the wire is 1500.Number of rope wires is assumed to be 2. Number of rope wires is assumed to be 2. Calculate the weight of wire if weight of 50m wire is 18kg. Calculate the force due to acceleration.
An elevator is assembled to raise equipment to a height of 22m. It is estimated that maximum weight of the material to be raised is 4.9kN. It is observed acceleration in such cases is 1.2m/s².10mm diameter wire ropes with fibre core are used. The tensile designation of the wire is 1500.Number of rope wires is assumed to be 2. Number of rope wires is assumed to be 2. Calculate the total load on wire rope neglecting the bending load if weight of 50m wire is 18kg.
There are two wires of same material and same length while the diameter of second wire is two times the diameter of first wire, then the ratio of extension the diameter of first wire, then the ratio of extension produced in the wire by applying same load will be _____________
Two wires have the same material and have the same volume. However wire 1 had cross sectional area A and wire 2 has cross sectional area 3A. If the length of wire 1 increases by ∆x on applying force F, how much force is needed to stretch wire 2 by the same amount?
An elevator is assembled to raise equipment to a height of 22m. It is estimated that maximum weight of the material to be raised is 4.9kN. It is observed acceleration in such cases is 1.2m/s².10mm diameter wire ropes with fibre core are used. The tensile designation of the wire is 1500. Number of wire ropes can be taken 2. Calculate the weight of material raised by each load.
For a four pole, 16 slot armature with two coil-side/slot having lap connected progressive winding has single turn coils. The same machine is then wave wound, the emf induced in the lap wound dc machine to that of wave wound will be ________
A piston-cylinder has the piston loaded with outside atmospheric pressure and piston mass to a pressure of 150 kPa. It contains water at −2°C, which is heated until the water becomes saturated vapour. Find the specific work for the process.