Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

A hollow rod has frictionless inner walls. Inside the rod are two small spheres that are kept on either side of the centre of rod. The rod is rotated about its central axis which is perpendicular to the plane of rotation. If the rod had been rotated by an impulsive torque which gave it an instantaneous angular velocity of 5rad/s, what will be the angular velocity after some finite but long time ‘t’? Assume no external forces act on rod after the impulse. Also state what will happen to the spheres in the centre of the rod. The rod has a mass =2kg & length =10cm. The two spheres have a mass =1kg each.
Which of the following heart valves are mechanical valves? i. Ball Valve ii. Autograft Valve iii. Xenograft Valve iv. Single Leaflet Valve v. Homograft Valve vi. Bi leaflet Valves
A rod is rotating about one end. If a force F1 acting on the other end produces a torque T & supplies power P, find the value of force F2 that will produce the same amount of power when it acts at the midpoint of the rod. Assume that all forces are perpendicular to the axis of rotation & axis of rod. The rod starts from rest.
The figure shows a 5 cm diameter rod, 90 cm long, which is having its lower face grinded smooth. The remainder of the rod is exposed to 32 degree Celsius room air and a surface coefficient heat transfer equal to 6.8 W/m2 degree exists between the rod surface and the room air. The grinder dissipates mechanical energy at the rate of 35 W. If thermal conductivity of rod material is 41.5 W/m degree, find the temperature of the rod at the point where the grinding is taking place
Piston diameter = 0.24 m, length of stroke = 0.6 m, length of connecting rod = 1.5 m, mass of reciprocating parts = 300 kg, mass of connecting rod = 250 kg; speed of rotation = 125 r.p.m; centre of gravity of connecting rod from crank pin = 0.5 m ; Kg of the connecting rod about an axis through the centre of gravity = 0.65 m Find angular acceleration of connecting rod in rad/s2.
Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
Two rods having thermal conductivity in the ratio of 5:3 having equal lengths and equal cross-sectional area are joined end to end. If the temperature of the free end of the first rod is 100°C and free end of the second rod is 20°C, then the temperature of the junction is?
A rod of 3 cm diameter and 20 cm length is maintained at 100 degree Celsius at one end and 10 degree Celsius at the other end. These temperature conditions are attained when there is heat flow rate of 6 W. If cylindrical surface of the rod is completely insulated, determine the thermal conductivity of the rod material
A 2" gate valve fitted in a pipe is replaced by a similar globe valve. Pressure drop in gate valve was Δp. For the same discharge, the pressure drop across globe valve is
Given a rod of length n and the selling prices of all pieces smaller than equal to n, find the most beneficial way of cutting the rod into smaller pieces. This problem is called the rod cutting problem. Which of these methods can be used to solve the rod cutting problem?