Bissoy.com
Doctors Medicines MCQs Q&A

_________ is used for cooling of products, mechanisms and factory machinery under control temperature.

_________ is used for cooling of products, mechanisms and factory machinery under control temperature. Correct Answer Chiller

Chillers are used for cooling of products, mechanisms and factory machinery under control temperature. These follow absorption refrigerant cycle or vapor compressionfor cooling a fluid. The basic principle is that heat always flows from hot to cold.

Related Questions

Factory A and Factory B employ 476 and 524 employees. respectively. The average weekly salary of an employee in Factory A is $34.5 whereas for an employee in Factory B it is $28.5, The standard deviation in paying the individual salary has been recorded as $5 and $4.5 for Factory A and Factory B, respectively. Which factory has greater variability in paying individual salary?
When demand for a factory's products is high, more money is spent at the factory for safety precautions and machinery maintenance than demand is low. Thus the average number of on-the-job accidents per employee each month should be bower during periods when demand is high than when demand is low and less money is available for safety precautions and machinery maintenance. Which of the following,if true about a factory when demand for its product is high casts the most serious doubt on the conclusion drawn above?
when demand for factory's products is high . more money is spent at the factory for safety precautions and machinery maintenance than when demand is low. thus the average number of on -the-job accidents per employee each month should be lower during perids when demand is high than when demand is low and less money is available for safety precautions and machinery maintenance .when demand for its products is high, casts the most serious doubt on the conclusion drawn above?
Consider the following statements for cooling towers: 1. Cooling tower is an artificial device used to cool the hot cooling water coming out of condenser more effectively. 2. The amount of water usually lost with induced draft cooling tower ranges from 5% to 6% by evaporation. 3. The amount of water usually lost with induced draft cooling tower ranges from 7% to 8% by drift losses. 4. The rate of evaporation of water and its cooling effect on the remaining water depends upon the relative humidity of air passing through the tower. Which of the above statements are correct?
Which of the following statements are true/false?
1. No child shall be employed or permitted to work, in any factory for more than four and a half hours in any day and during the night.
2. A child who has completed his eighteenth year or an adolescent shall not be required or allowed to work in any factory unless he has a certificate of fitness is granted in the custody of the manager of the factory.
3. The period of work of all children employed in a factory shall be limited to two shifts which shall not overlap or spread over more than five hours each.
4. No female child shall be required or allowed to work in any factory except between 8 A.M. and 7 P.M.
The bypass factor, in case of sensible cooling of air, is given by (where td₁ = Dry bulb temperature of air entering the cooling coil, td₂ = Dry bulb temperature of air leaving the cooling coil, and td₃ = Dry bulb temperature of the cooling coil)
The bypass factor, in case of sensible cooling of air, is given by (where td1 = Dry bulb temperature of air entering the cooling coil, td2 = Dry bulb temperature of air leaving the cooling coil and td3 = Dry bulb temperature of the cooling coil)
There are 1250 cars in a factory. The factory produces 5 cars hourly. If the sales of the factory are 50 cars per day, what will be the sale percentage to the total cars held by the factory after 5 days. It is known that the factory runs 8 hours daily.
Which of the following is/are the advantages of using a control chart for inspection? (i) A control chart indicates whether the process is in control or out of control. (ii) A control chart determines process variability. (iii) A control chart ensures product quality. (iv) Scrap or percentage reduction can be reduced by taking the necessary actions in time against the warnings indicated by control charts. (v) Control charts build up the reputation of the organization through customer’s satisfaction. (vi) The control chart can detect the unusual variations taking place in a process.
Planar mechanisms and spherical mechanisms are included under spatial mechanisms. True or false?