Bissoy.com
Doctors Medicines MCQs Q&A

What type of heat exchanger is used in cryogenic applications?

What type of heat exchanger is used in cryogenic applications? Correct Answer Plate fin heat exchanger

Plate fin heat exchangeris used in cryogenic applications. They use corrugated fins which are separated by flat plates. These are used in gas-to-gas applications at where it has low pressures and temperatures not above 800°C.

Related Questions

Which of the following statements about Printed circuit heat exchanger are correct? Statement 1: Printed circuit heat exchanger is an example for direct heat exchanger. Statement 2: It has high heat transfer surface area per unit volume of the exchanger.
Plate type heat exchangers have less surface area as compared to a similar Shell and Tube heat exchanger. A Shell and Tube Heat Exchanger of equivalent area weigh six-seven times less than a Plate Type heat exchanger.
A Windows 2000 Server computer named server2 runs numerous 32bit applications and two 16bit applications. Users start the 16bit applications by running APP1.EXE for one application and APP2.EXE for another application. The 16bit applications are configured to run in the separate memory space. You want to create a performance base like chart in the system monitor for all the applications on server2. You add all of 32bit applications and now you want to add two 16bit applications. What should you do?
Forced air flows over a convection heat exchanger in a room heater, resulting in a convective heat transfer coefficient 1.136 k W/m2 K. The surface temperature of heat exchanger may be considered constant at 65 degree Celsius, and the air is at 20 degree Celsius. Determine the heat exchanger surface area required for 8.8 k W of heating
A cold fluid (specific heat 2.95 k J/kg K) at 10 kg/min is to be heated from 25 degree Celsius to 55 degree Celsius in a heat exchanger. The task is accomplished by extracting heat from hot water (specific heat 4.186 k J /kg K) available at mass flow rate 5 kg/min and inlet temperature 85 degree Celsius. Identify the type of arrangement of the heat exchanger
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
A heat exchanger with heat transfer surface area A and overall heat transfer coefficient U handles two fluids of heat capacities Cmax and Cmin. The number of transfer units (NTU) used in the analysis of heat exchanger is specified as
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is