The ratio between shear stress and shear rate in a fluid is called __________

The ratio between shear stress and shear rate in a fluid is called __________ Correct Answer viscosity

The ratio between shear stress and shear rate in a fluid is called viscosity. Bulk modulus can be defined as the relative change in volume of the object produced by tensile stress acting homogenously over its surface. Specific density is the ratio of density of the substance to density of a given reference material. Young’s modulus is defined as the ratio of tensile stress to tensile strain of a given material.
Bissoy MCQ

Related Questions

Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
Shear stress versus shear rate behavior of four different types of fluids (I, II, III and IV) are shown in the figure below.
Basic Principles of Biotechnology mcq question image
Which one of the following options is correct?
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the __________ stress.
Bernoulli's equation for fluid flow is derived following certain assumptions. Out of the assumptions listed below, which set of assumptions is used in derivation of Bernoulli's equation?
1. Fluid flow is frictionless & irrotational
2. Fluid flow is steady
3. Fluid flow is uniform & turbulent
4. Fluid is compressible
5. Fluid is incompressible
A wall bracket is attached to the wall by means of 2 identical bolts, one at A and one at B. The force of 20kN acts at a distance of 400mm. Bolt A lies at a distance of 50mm from axis of tilt and bolt B 500mm. Allowable shear stress in the bolts is 100N/mm² and tensile is 40N/mm². Find the radius of Mohr circle which can be made from the shear stress and tensile stress acting on bolts.(Consider bolt under max stress and area of bolt is A)
Which of the following statements regarding stress related factors is/are true and false?
1. Burnout Stress Syndrome (BOSS) is a debilirating psychological condition brought about by unrelieved work stress.
2. 'Good' and 'bad' stresses are also referred to as 'Distress' and 'Eustress' respectively.
3. It is natural and healthy to maintain optimal level of stress.
4. Rustout Stress Syndrome (ROSS) is indicative of stress overload.
5. Anxiety is a state of emotional tension characterised by Apprehension, fearfulness, and psychic pain.
If nominal shear stress $${\tau _{\text{v}}}$$ exceeds the design shear strength of concrete $${\tau _{\text{c}}}$$, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid.