Bissoy.com
Doctors Medicines MCQs Q&A

Which type of columns are used for liquid dispersion in a continuous gas phase?

Which type of columns are used for liquid dispersion in a continuous gas phase? Correct Answer Packed

Packed Beds. Although packed bed columns are used most often for absorption, they are also used for the distillation of vapor-liquid mixtures. The packing provides a large surface area for vapor-liquid contact, which increases the column’s effectiveness.

Related Questions

Consider the following pairs. S. No. Dispersed Phase Dispersing Medium Type 1. Liquid Gas Aerosol 2. Gas Liquid Foam 3. Liquid Liquid Emulsion 4. Liquid Solid Solid Sol   Which are the correct pairs?
__________ columns are used for liquid dispersion in a continuous gas phase.
Which of the following statements is/are correct with respect to a Scott-connected transformer? I. It can do 3-phase to 2-phase conversion II. It can do 2-phase to 3-phase conversion III. It can do 2-phase to 4-phase conversion IV. It can do 3-phase to 4-phase conversion
The following question, there are three statements I, II and III. Read the question carefully and mark your answer according to which statements(s) is/are sufficient to the answer the question. What proportion of liquid of type C is there in the tank of capacity 60 liters after 2 minutes if the tank is initially empty? Statement I: Three pipes P, Q, R fill the tank in 15 minutes, 12 minutes and 10 minutes respectively Statement II: When the tank was empty all the three pipes are opened and they discharge three different types of liquid Statement III: Pipe P discharge type A liquid, pipe Q discharge type B liquid and Pipe R discharge type C liquid
The network formed by resistors and capacitors for modifying the rate of change of gain and the phase shift is called a compensating network. Which of the following statements are not correct ? (A) The main purpose of a compensating network is to modify the performance of op-amp ciruit over the desired frequency range (B) There are two types of op-amps : internally compensated and externally compensated (C) 741 C is an externally compensated op-amp while 709 C is internally compensated op-amp (D) The phase lag and phase lead are most commonly used compensating networks in op-amps (E) Phase lag contributes a positive phase angle and phase lead a negative phase angle Choose the most appropriate answer from the options given below : 
Experiments were conducted to determine the flux of a species A in a stagnant medium across a gas-liquid interface. The overall mass transfer co-efficient based on the liquid side for dilute systems for the above was estimated to be 4 × 10-3 kg mole/m2.s. The equilibrium data for the system is given as y = 2x. The flux across the interface (in kg mole/m2.s) for bulk concentrations of A in gas phase and liquid phase as y = 0.4 and x = 0.01 respectively is
In a wetted-wall tower, an air-H2S mixture is flowing by a film of water which is flowing as a thin film down a vertical plate. The H2S is being absorbed from the air to the water at a total pressure of 1.50 atm abs and 30oC. The value of kc of 9.567×10-4 m/s has been predicted for the gas-phase mass-transfer coefficient. At a given point the mole fraction of H2S in the liquid at the liquid-gas interface is 2.0×10-5 and pA of H2S in the gas is 0.05 atm. The Henry’s law equilibrium relation is pA(atm) = 609xA (mole fraction in liquid). Calculate the rate of absorption of H2S.
A single mode fiber has a zero dispersion wavelength of 1.21μm and a dispersion slope of 0.08 psnm-2km-1. What is the total first order dispersion at wavelength 1.26μm.
A single mode fiber has a zero dispersion wavelength of 1.21μm and a dispersion slope of 0.08 psnm-2km-1. What is the total first order dispersion at wavelength 1.26μm.
In a newly developed innovative idea brought up by CSIR in India, gas turbine exhaust gas are being utilized to convert feedwater into steam. Certain data of the experiment are as follows: mass flow rate of exhaust gas = 40 kg/hr, enthalpy of exhaust gas at the time of their exit from gas turbine is 600 kJ/kg, steam turbine output as measured by brake dynamometer = 60 hp-sec, thermal efficiency of steam power plant is 0.25, efficiency of exhaust gas in converting feedwater into steam is taken as 50%. Find the enthalpy of exhaust gas remaining after they generate steam from feedwater?