Bissoy.com
Doctors Medicines MCQs Q&A

For ductile material to cause shearing, the penetration of tool along the thickness should be _____ whereas for brittle material it is ________

For ductile material to cause shearing, the penetration of tool along the thickness should be _____ whereas for brittle material it is ________ Correct Answer high, low

In shearing process, the tool penetrated the sheet metal along its thickness; this causes the shearing and complete breaking of the sample. So, if the material is brittle on small penetration the material will shear off whereas on the ductile metal more considerable penetration will be required.

Related Questions

Which of the following forces are measured directly by strain gauges or force dynamometers during metal cutting? 1. Force exerted by the tool on the chip acting normally to the tool face 2. Horizontal cutting force exerted by the tool on the workpiece 3. Frictional resistance of the tool against the chip flow acting along the tool face 4. Vertical force which helps in holding the tool in position Select the correct answer using the codes given below.
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of the four alternatives. The modes of action are _____ in science and religion. Science relies on experiment, whereas religion is based on experience. Any religious _____ whether it is Christs or Ramakrishnas is personal and _____ . Science, on the other hand is marked by objectivity. Theory has to be corroborated by _____ proof providing material comforts. The frontiers of science do not end in knowledge but are _____ to the formation of appliances for actual use. whereas religion is based on experience. Any religious _____ whether
Thickness of 8 tyres L, M, N, O, P, Q, R and S is compared. Thickness of no two tyres is same. Thickness of N is more than L but less than 6 tyres. Thickness of O is more than M but less than Q. Thickness of P is less than only two tyres. Thickness of Q is not more than P. Which of the following statement is not correct?
Consider the following statements: 1. HSS tools wear very rapidly, whereas in cemented carbide tools, even though hardness is retained, crater wear can occur due to solid-state diffusion. 2. Cutting tools made of Super-HSS, also known as cobalt-based HSS, are made by adding 2% to 15% of cobalt which increases the cutting efficiency at heavier cuts by increasing the hot hardness and wear resistance. 3. Tools failure due to excessive stress can be minimized by providing small or negative rake angles on brittle tool materials, protecting tool tip by providing large side-cutting edge angles, and honing a narrow chamfer along the cutting edge. Which of the above statements are correct?
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of the four alternatives. The modes of action are _____ in science and religion. Science relies on experiment, whereas religion is based on experience. Any religious _____ whether it is Christs or Ramakrishnas is personal and _____ . Science, on the other hand is marked by objectivity. Theory has to be corroborated by _____ proof providing material comforts. The frontiers of science do not end in knowledge but are _____ to the formation of appliances for actual use. Theory has to be corroborated by _____ proof providing material comforts.
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of thefour alternatives.
Democracy should _____ dignity of the individual. It should also aim at the _____ good of the greatest _____. The opposition party should _____ the wrong plans,
policies and decisions of the government in power. The government should cater to the _____ needs of the people to make its position solid.
Democracy should _____ dignity of the individual.
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of thefour alternatives.
Democracy should _____ dignity of the individual. It should also aim at the _____ good of the greatest _____. The opposition party should _____ the wrong plans,
policies and decisions of the government in power. The government should cater to the _____ needs of the people to make its position solid.
It should also aim at the _____ good
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of thefour alternatives.
Democracy should _____ dignity of the individual. It should also aim at the _____ good of the greatest _____. The opposition party should _____ the wrong plans,
policies and decisions of the government in power. The government should cater to the _____ needs of the people to make its position solid.
should _____ the wrong plans, policies and decisions of the government in power.
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of thefour alternatives.
Democracy should _____ dignity of the individual. It should also aim at the _____ good of the greatest _____. The opposition party should _____ the wrong plans,
policies and decisions of the government in power. The government should cater to the _____ needs of the people to make its position solid.
The government should cater to the _____ needs of the people to make its position solid.
In the following passage some of the words have been left out. Read the passage carefully and select the correct answer for the given blank out of thefour alternatives. The modes of action are _____ in science and religion. Science relies on experiment, whereas religion is based on experience. Any religious _____ whether it is Christs or Ramakrishnas is personal and _____ . Science, on the other hand is marked by objectivity. Theory has to be corroborated by _____ proof providing material comforts. The frontiers of science do not end in knowledge but are _____ to the formation of appliances for actual use. The modes of action are _____ in science and religion.