Bissoy.com
Doctors Medicines MCQs Q&A

A screw-driven constant head velocity machine for tensile testing machine are _________

A screw-driven constant head velocity machine for tensile testing machine are _________ Correct Answer displacement controlled machine

A mechanical screw controlled machine with constant head velocity, have only freedom of having a uniform elongation of the sample. So, it is called strain-controlled or displacement controlled machine.

Related Questions

Two centrifugal pumps P and R are available for use in a pipe flow system and their head-discharge characteristics are as follows. Pump P Pump R Discharge (cumecs) Head (m) Discharge (cumecs) Head (m) 0 40 0 45 0.12 35 0.14 40 0.2 28 0.24 35 0.3 18 0.3 28   The following statements (S1, S2, and S3) pertain to the head and discharge values during actual operation. Neglect losses in the system. Which of the following statements are correct? S1: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 35 m. S2: When the two pumps P and R are connected in parallel, the discharge is 0.36 cumecs corresponding to a head of 70 m. S3: When the two pumps P and R are connected in series, the discharge is 0.3 cumecs corresponding to a head of 46 m.
What is the normal order of activities in which traditional software testing is organized ? (a) Integration Testing (b) System Testing (c) Unit Testing (d) Validation Testing
If the crosshead of the tensile testing machine is moving with constant velocity v, then after time t, the total displacement of crosshead will be vt. A specimen is held between the crosshead of the machine. The total displacement in the sample will be ______________
The important parameters describing the performance of a hydraulic machine are: P the power input, H the head produced across the machine and the efficiency, η. For a given geometrical design of the machine, the performance is characterized by the variables: H – the head increase across the machine ρ – the fluid density, ω – the angular velocity of the rotor, D – the diameter of the rotor, μ  – the fluid viscosity and Q – the flow rate; and both P and η are expressed through these variables. How many non-dimensional parameters are involved herein? Gravitational acceleration g has also to be considered necessarily?
Match the items of List - II with the items of List - I and select the code of correct matching List - I List - II (a) Chi-square Test (i) Testing the significance of the differences of the mean values among more than two sample groups. (b) ANOVA (F-test) (ii) Testing the goodness of fit of a distribution (c) Z - test (iii) Testing the significance of the difference of the mean values between two large sized samples (d) t - test (iv) Testing the significance of the difference of the mean values between two small sized samples when population standard deviation is not available  
Which one of the following four addresses is NOT EXACTLY the same as the one given below? Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (i) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (ii) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094 (iii) Robert S Ingram 1998 Revocable 8 Shaftsbary Ln Hilton Head Island, SC 29926 (843) 342­7094 (iv) Robert S Ingram 1998 Revocable 8 Shaftsbury Ln Hilton Head Island, SC 29926 (843) 342­7094
Group I shows different heat addition processes in power cycles. Likewise, Group II shows different heat removal processes. Group III lists power cycles. Match items from Groups I, II and III. Group I Group II Group III P. Pressure constant S. Pressure constant 1. Rankine cycle Q. Volume constant T. Volume constant 2. Otto cycle R. Temperature constant U. Temperature constant 3. Carnot cycle     4. Diesel cycle     5. Brayton cycle
Which of the following parameters is actually measured during tensile testing of a specimen using Universal testing machine?
A tensile specimen was deformed at a constant cross head speed of 6 mm/min. The strain rate at the start of the testing was 5 × 10-3 s-1. The initial gauge length of the specimen (in mm) was
Calculate ultimate moment and shear of effective span is 30m, live load is 9kn/m, dead load excluding self weight is 2kn/m, load factors for dead load is 1.4 for live load is 1.6 cube strength of concrete fcu is 50n/mm2 cube strength at transfer is fci is 35n/mm2, tensile strength of concrete Ec is 34kn/mm2 loss ratio ɳ is 0.85 and 8mm diameter high tensile strength fpu is 1500n/mm2 are available for use and the modulus of elasticity of high tensile wires is 200kn/mm2?