Bissoy.com
Doctors Medicines MCQs Q&A

The rate of strain hardening and strain hardening exponents in the flow curve is always the same.

The rate of strain hardening and strain hardening exponents in the flow curve is always the same. Correct Answer False

The flow curve is expressed as: -> σ=Kεn Where the n is strain hardening exponent. The rate is strain hardening is defined as the change in stress values as the strain is increased.

Related Questions

From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
The true strain rate is given as ϒ, and conventional strain rate is given as ε. The engineering strain is equal to e. The relationship between conventional strain rate and true strain rate is _______
In the flow curve equation given below, if the value of strain hardening exponent is increased, what will be the effect on the ductility of material? σ=Kεn; Where n is strain hardening exponent.
Match the following in Column X with Column Y: Column X Column Y  P. In a triaxial compression test, with increase of axial strain in loose sand under drained shear condition, the volumetric strain  I. decreases  Q. In a triaxial compression test, with increase of axial strain in loose sand under undrained shear condition, the excess pore water pressure  II. Increase  R. In a triaxial compression test, the pore pressure parameter “B” for a saturated soil  III. remains same  S. For shallow strip footing in pure saturated clay, Terzaghi’s bearing capacity factor (Nq) due to surcharge  IV. is always 0.0.      V. is always 1.0.      VI. is always 0.5. Which one of the following combinations is correct?
The MC curve reaches its minimum point before the AVC curve and the AC curve. In addition the MC curve intersects the AVC curve and the AC curve at their lowest point. The above statements are both true
Strain hardening due to ___________ process arises from short range force occurring over a distance of 5 to 10 atomic distance. This hardening can be overcome at finite temperatures with the help of thermal fluctuations, and therefore, it is temperature and strain-rate-dependent.
Which of the following statements are true/false?
1. A minimum rate of wages for the time spent by employees for the production of output is minimum time rate.
2. Minimum piece rate is the rate based on the quantity of the output employees have produced.
3. The guaranteed time rate is a minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis.
4. A minimum rate of remuneration to apply in the case of employees employed on piece work for the purpose of securing to such employees a minimum rate of wages on a time work basis is overtime rate.
The most common form to express the flow curve is: σ=Kεn Here σ=stress, ε=strain, n=strain hardening exponent, and K is defined as stress when ε = _______
The strain hardening behaviour of an annealed rod during cold rolling is given by σ = 700 $${\left( \in \right)^{0.2}}$$ MPa. where σ is the flow stress at strain $$ \in $$.
Flow stress after 50% reduction in area of the annealed rod on cold rolling is approximately
The question below consists of a set of labelled sentences. Out of the four options given, select the most logical order of the sentences to form acoherent paragraph.
P- The magnitude of the interdependence depends on the technique of production causing the shifts in the food supply curve.
Q- Interdependence of food and labour market is important for the development process.
R- Similarly, an upward shift in the food supply curve shifts up the food demand curve.
S- An upward shift in the food supply curve would simultaneously result in an upward shift in the labour demand curve.