Bissoy.com
Doctors Medicines MCQs Q&A

Related Questions

Consider the following statements pertaining to heat transfer through fins (i) They must be arranged at right angles to the direction of flow of working fluid (ii) The temperature along the fin is variable and accordingly heat transfer rate varies along the fin elements (iii) Fins are equally effective irrespective whether they are on the hot side or cold side of the fluid (iv) Fins are made of materials that have thermal conductivity higher than that of wall Identify the correct statements
Which of the following statements about Printed circuit heat exchanger are correct? Statement 1: Printed circuit heat exchanger is an example for direct heat exchanger. Statement 2: It has high heat transfer surface area per unit volume of the exchanger.
Forced air flows over a convection heat exchanger in a room heater, resulting in a convective heat transfer coefficient 1.136 k W/m2 K. The surface temperature of heat exchanger may be considered constant at 65 degree Celsius, and the air is at 20 degree Celsius. Determine the heat exchanger surface area required for 8.8 k W of heating
Plate type heat exchangers have less surface area as compared to a similar Shell and Tube heat exchanger. A Shell and Tube Heat Exchanger of equivalent area weigh six-seven times less than a Plate Type heat exchanger.
An electronic semiconductor device generates 0.16 k J/hr of heat. To keep the surface temperature at the upper safe limit of 75 degree Celsius, it is desired that the heat generated should be dissipated to the surrounding environment which is at 30 degree Celsius. The task is accomplished by attaching aluminum fins, 0.5 square mm and 10 mm to the surface. Work out the number of fins if thermal conductivity of fin material is 690W/m K and the heat transfer coefficient is 45k J/square m hr K. Neglect the heat loss from the tip of the fin
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the effectiveness of the heat exchanger. At the condensing pressure, stream has a saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to the water. Take specific heat of water as 4 k J/kg K
In a surface condenser, the water flowing through a series of tubes at the rate of 200 kg/hr is heated from 15 degree Celsius to 75 degree Celsius. The steam condenses on the outside surface of tubes at atmospheric pressure and the overall heat transfer coefficient is estimated at 860 k J/m2 hr degree. Find the number of transfer units of the heat exchanger. At the condensing pressure, stream has saturation temperature 0f 100 degree Celsius and the latent heat of vaporization is 2160 k J/kg. Further, the steam is initially just saturated and the condensate leaves the exchanger without sub-cooling i.e. only latent heat of condensing steam is transferred to water. Take specific heat of water as 4 k J/kg K
It is said that fins can take a variety of forms (i) Longitudinal fins of rectangular cross section attached to a wall (ii) Cylindrical tubes with radial fins (iii) Conical rod protruding from a wall Identify the correct statement
Air is to be heated by condensing steam. Two heat exchangers are available (i) a shell and tube heat exchanger and (ii) a finned tube heat exchanger. Tube side heat transfer area are equal in both the cases. The recommended arrangement is
In a counter flow heat exchanger, water flowing through a tube of 10 cm inner diameter is heated by steam condensing on the outside of the tube. The convective film coefficient on the water and steam side are estimated to be 12000 and 20000 k J/m2 hr degree. Neglecting tube thickness and its resistance to heat flow, workout the overall heat transfer coefficient for the heat exchanger